Frigidaire Washer FTF2140FS2 Leaking

The Tub to Pump Hose is an OEM part for Frigidaire washing machines. This part directs water from the tub to the pump during the wash cycle. This flexible hose plays a role in the machine's ability to drain water efficiently after each wash or rinse cycle, ensuring optimal performance. 

Causes for replacement might include wear and tear over time that leads to cracks or holes in the hose, blockages that prevent water from draining properly, or improper installation that results in leaks or water retention. 

Symptoms of a bad Tub to Pump Hose include:

• Leaks found underneath the washing machine
• Problems with the washing machine draining properly
• Puddles of water appearing during or after a wash cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Boot Seal is an OEM part for Frigidaire washing machines. It is a flexible gasket that forms a seal between the washing machine door and the drum, preventing water from leaking during the wash cycle.

Causes of a bad door boot seal can include wear and tear over time, mold or mildew buildup, or physical damage from sharp objects or improper loading of the washer. Exposure to harsh cleaning chemicals can also degrade the seal, leading to leaks.

Symptoms of a bad door boot seal include:

• Water leaking from the front of the washing machine
• Visible tears or cracks in the seal
• Mold or mildew buildup on the seal
• A musty odor coming from the washing machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Outer Bellow Clamp is an OEM Replacement Part designed for Frigidaire front-load washing machines. Its role is to securely hold the door boot in place, ensuring a tight seal that prevents leaks during operation. This clamp is attached to the front panel of the washer, and its installation requires the machine to be unplugged for safety.

Causes of a faulty outer bellow clamp can include wear and tear over time, damage due to excessive force or tension, or corrosion from exposure to water and detergent.

Symptoms of a bad outer bellow clamp may include:

• Water leaking from the washer door or around the door boot seal
• Loose or misaligned door boot seal
• Visible damage or deformation of the clamp

This clamp is compatible with select Frigidaire brand models including Crosley, Electrolux, Kenmore, and White Westinghouse.

The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle. 

Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.

Symptoms of a bad Frigidaire Drain Pump include:

• Water not draining completely from the washer
• Unusual noises, like humming or buzzing, indicating the pump is struggling
• Washer stopping mid-cycle
• Water pooling around the base of the machine

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is the water inlet valve that controls the flow of household water into your washer during fill and rinse. Replacing a failing valve restores proper filling performance and helps stop unintended water entry when the machine is idle.

• Opens and closes to allow the correct amount of water into the washer as commanded by the control
• Failure can cause no fill, slow/long fill, or continuous filling/fill when off
• Leaks from the valve body or hose connections indicate the valve should be replaced
• Electrical coil failure may lead to intermittent or no operation

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; label and disconnect hoses and wiring
• Install the new valve; transfer any brackets or clips from the old part if needed
• Restore water and power, then check all connections for leaks and run a test fill

The Dispenser to Tub Hose is an OEM part for Frigidaire washing machines. This hose is responsible for transporting detergent and other cleaning agents from the dispenser to the tub during the wash cycle.  

Common causes of a bad hose include constant exposure to water and detergent, which can lead to wear and tear, blockages from detergent buildup, or physical damage such as cracks and splits.

Symptoms of a bad dispenser to tub hose include:

• Water leaks near the detergent dispenser
• Uneven or insufficient distribution of detergent
• Visible cracks, splits, or other damage to the hose
• Error codes on the washing machine related to water flow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning