Kenmore Washer 110.20052994 (11020052994, 110 20052994) Will not agitate or doesn't agitate

The Washer Agitator Dog set is a set of 4 OEM replacement parts for Whirlpool and Kenmore washing machines, designed to engage the agitator, allowing it to move in one direction and lock in the opposite direction. The agitator dogs also come available in the agitator repair kit WP8537433. Check your model number for compatibility.

Symptoms of failing Agitator Dogs include:

• The agitator not moving
• Only moving in one direction
• Clothes not getting cleaned due to lack of agitation
• Clothes becoming tangled

Causes of bad Agitator Dogs can range from normal wear and tear, which gradually erodes their teeth, making them too smooth to engage the agitator properly, to overloading the washing machine, which puts extra stress on the agitator and accelerates the wear of the dogs.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Direct Drive Washer Motor Coupling is an OEM replacement part for Whirlpool washers. It is responsible for connecting the motor to the transmission, allowing the washer to agitate and spin the clothes during the wash and spin cycles.

A bad motor coupling can be caused by prolonged use, heavy loads, or overloading the washer. It can also wear out or break over time due to normal usage.

Symptoms of a bad motor coupling include:

• The washer not agitating or spinning.
• Unusual noises, such as grinding or rattling, during operation.
• The motor running but the drum not moving.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This agitator cam is the replacement cam that fits under the washer agitator to engage the transmission and help transfer motion. Replacing a worn or broken cam restores secure agitator engagement for reliable washing action. What it does:

• Locks the agitator to the drive so the agitator oscillates and reverses during wash cycles
• Replaces a damaged or worn cam that can cause the agitator to slip, spin freely, or fail to agitate
• Works with the agitator assembly and dogs to maintain proper drive engagement
• Restores proper mechanical linkage between the agitator and the washer transmission

• Disconnect power and water supply before beginning any repair
• Remove the agitator, inspect agitator dogs and splines for wear, and replace if needed
• Install the cam into the agitator and reassemble in reverse order of removal following the OEM service instructions
• After reassembly, run a short test cycle to ensure the agitator engages and functions correctly

The Transmission is an OEM part for Whirlpool washing machines. This integral component is at the heart of the washing machine's operation, translating the motor's power into action by driving the agitator and spinning the drum. 

Regular inspection and maintenance can prolong the life of the transmission, but if these symptoms occur, it may be time to replace this critical component. 

Symptoms of a bad Transmission include:

• The washing machine making unusual noises during the wash or spin cycles, such as grinding or whining sounds.
• The washer failing to agitate properly, affecting the cleanliness of the laundry.
• The drum not spinning during the spin cycle, leaving clothes wetter than usual.
• Leakage of transmission fluid beneath the washing machine.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Rubber grommet for motor mount stud.

This driven cam bearing supports the cam in the compactor's drive assembly, reducing friction and keeping components aligned so the ram moves smoothly and the unit completes and reverses cycles reliably.

• Supports and centers the driven cam/gear for proper alignment
• Reduces friction and wear for smoother cam rotation
• Helps ensure correct switch timing so the ram reverses at end of travel
• Symptoms of wear include squealing/grinding, binding or jerky ram movement, or failure to complete a cycle

• Disconnect power at the breaker or unplug the unit before servicing
• Secure the drawer/ram to prevent unintended movement while working
• Access the drive mechanism and note the bearing's orientation on the cam before removal
• Seat the new bearing fully and hand-rotate the cam to verify smooth movement before reassembly and restoring power