Magic Chef Washer CAV2004AWW Leaking

The Washer Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the washer tub to the drain pump, facilitating the proper drainage of water from the tub during the wash and spin cycles.  

Causes of a bad tub to pump hose can include wear and tear from frequent use, blockages from lint or debris, and damage from overloading the washer or mishandling during maintenance.  

Symptoms of a bad tub to pump hose include:

• Leaks during the wash or spin cycles
• Water not draining properly from the washer
• Visible cracks, holes, or wear in the hose
• Unusual noises during the drain cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Washer Drain Pump Assembly is an OEM part for Whirlpool washing machines. This component is vital for draining water from the washer drum during the wash and rinse cycles. The pump forces water out of the drum and through the drain hose, ensuring that clothes are cleaned and rinsed effectively.

Symptoms of a failing Washer Drain Pump Assembly include:

• Water not draining from the washer, leaving clothes wet
• Unusual noises during the drain cycle, such as humming or grinding
• Error codes on the washer's display indicating drainage issues
• Water leaks from the pump area or from the washer
• The washer stopping mid-cycle due to drainage problems

Causes of a bad drain pump assembly can include obstructions from debris, wear and tear on the pump motor over time, electrical issues such as short circuits, or damage from improper installation or usage.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Note: This pump has been redesigned and the mounting plate is no longer required. It now mounts directly to the base of the washer.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Water Inlet Valve Assembly is an OEM part for Whirlpool washing machines. This valve controls the flow of water into the washer during the fill cycles, ensuring the right amount of water is used for washing and rinsing. It plays a crucial role in the overall efficiency and functionality of the washing machine.

Common causes of a bad water inlet valve include sediment buildup, electrical failures, or damage to the valve components.

Symptoms of a bad water inlet valve assembly include:

• The washer not filling with water or filling slowly
• Water leaking from the valve area
• The washer filling with water even when it's turned off
• Error codes related to water intake issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This gasket seals the basket to the center shaft to help prevent leaks and reduce noise from worn or damaged seals. It restores a proper seal between the tub/basket and the drive shaft for reliable operation. What it does:

• Seals the gap between the basket/tub and the center drive shaft to help prevent water from leaking into the motor/tub area
• Helps reduce rubbing noise caused by a worn or torn seal
• Restores a tight fit after seal failure, wear, or damage
• Common symptom: water leakage from the tub area or visible wear around the shaft opening

• Refer to the exploded parts diagram for correct positioning and orientation
• Inspect mating surfaces for damage or residue and clean before installing the new gasket
• Replace only when the appliance is unplugged and water supply is turned off; follow safety procedures for draining and securing the unit
• If other components show wear (shaft seals, basket, or fasteners), replace them as recommended by the OEM

This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.

• Connects the washer's drain outlet to the household standpipe or laundry tub
• Molded bend helps position the hose correctly and reduces kinking
• Typical symptoms: water leaking at the back or onto the floor while draining
• Visible splits, soft spots, brittleness, or abrasion on the hose
• Slow or incomplete draining caused by kinks or internal blockage

• Disconnect power and move the washer to access the rear; shutting off water is recommended as a precaution
• Place towels or a shallow pan to catch residual water when removing the old hose
• Transfer and reuse existing clamps/brackets if required; fully seat and secure connections, and route the hose to avoid kinks or rubbing
• Insert the outlet end properly into the standpipe or tub per your model's instructions, then run a quick drain/spin to check for leaks

The Washer Drive Belt is an OEM part for Whirlpool washing machines. It is crucial for transmitting the power from the motor to the drum, enabling the washing machine to tumble and spin during the wash and spin cycles. The drive belt wraps around the motor and drum pulleys, providing the necessary traction and tension to operate efficiently.

Causes of a bad Washer Drive Belt can include stretching over time, which reduces its efficiency to grip the pulleys properly, or fraying and cracking due to age and normal wear and tear. Misalignment or improper installation can also lead to premature belt failure.

Symptoms of a bad Washer Drive Belt include:

• The washing machine failing to spin or agitate.
• A burning smell or unusual noises during operation, indicating slippage or rubbing.
• Visible signs of wear like cracks, fraying, or noticeable looseness on the belt.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation