Maytag Dishwasher JDB1255AWS2 Leaking

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

Bottom

This seal sits at the dishwasher's air/water inlet, creating a tight barrier where the inlet assembly meets the tub or door. Replacing a worn seal helps stop nuisance leaks and supports proper fill and venting performance. What it does

• Forms a watertight seal at the air/water inlet connection
• Helps prevent drips or seepage during fill and wash
• Supports correct venting to keep moisture contained inside the tub
• Common failure signs include water on the floor near the unit, dampness around the inlet/vent area, or a cracked, flattened, or brittle seal

• One air/water inlet seal

• Disconnect power and shut off water before servicing
• Access method varies by model; remove the inlet/vent cover or side panel to reach the seal
• Clean mating surfaces; seat the new seal evenly without distortion
• Reassemble and run a brief fill/wash to check for leaks

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Located on the supply tube behind the upper dishwasher rack.

This Tub Edge Trim (bottom) fits along the lower edge of the dishwasher tub opening. Replacing a cracked, warped, or missing trim restores a clean finished edge and helps the door open and close smoothly without rubbing or snagging.

• Finishes and protects the bottom lip of the tub opening
• Helps maintain proper clearance for the door panel and gasket
• Replaces damaged, warped, discolored, or missing trim
• Typical symptoms: loose or broken strip, rubbing when closing, visible gap along the lower edge

• Disconnect power to the dishwasher before servicing
• Open the door and remove the old trim by releasing its retaining tabs or screws; note orientation
• Align the new trim on the lower tub edge and press or fasten until fully seated across the opening
• Verify the door closes freely and the gasket seats evenly before restoring power

Replacement pump gasket with silicone sealing material that restores a watertight seal between the pump and housing. Helps stop leaks at the pump area and prevents water pooling under the appliance.

• Seals the pump to the housing to help prevent water leaks and drips.
• Common repair for visible water under the appliance or leaks coming from the pump area.
• Silicone sealing material provides a flexible, water-tight interface that conforms to the pump housing.
• Designed to replace the factory pump gasket for a direct fit and proper sealing.

• Disconnect power and water supply before beginning any repair.
• Remove the pump assembly to access and replace the gasket.
• Clean and dry mating surfaces before installing the new gasket; seat evenly to ensure a full seal.