Maytag Dishwasher JDB3600AWS2 Leaking

Dishwasher leaking from underneath? The float switch kit controls water level and stops overfilling. Typical repair time 10-30 minutes.

Dishwasher not filling with water? A faulty water inlet valve prevents water flow during wash cycles. DIY-friendly repair in about 15 minutes.

Flexible drain hose carries wastewater from your dishwasher to the kitchen drain. Replace if cracked, leaking, burst, or damaged by wear or pests.

Carries wastewater from your dishwasher to the household drain. Replace if cracked, punctured, or leaking. Installs at pump outlet and drain connection.

The Diverter Motor is an OEM part for Whirlpool dishwashers. It controls the movement of the diverter disc, which directs water flow to different spray arms during the wash cycle. This ensures that all areas of the dishwasher receive adequate water pressure for effective cleaning.

Causes of a bad diverter motor can include electrical malfunctions, wear and tear from frequent use, or damage from water exposure. A faulty diverter motor can prevent the proper distribution of water, leading to poor cleaning performance.

Symptoms of a bad diverter motor include:

• Dishes not being cleaned properly
• Unusual noises coming from the dishwasher during operation
• The dishwasher not advancing through cycles correctly
• Water not reaching all areas of the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Includes wire harness WPW10083167, Drain cap part number WPW10193605, and the shaft seal has been incorporated into sump housing, not available separately.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rubber Washer is an OEM part for Whirlpool dishwashers. This washer plays a role in ensuring a leak-proof seal at various connection points within the dishwasher, such as at the water inlet valve or hose connections. Its primary function is to prevent water from leaking out of the dishwasher during operation, thereby ensuring efficient and safe use of the appliance. 

Over time, rubber washers can deteriorate due to the constant exposure to water and chemicals found in dishwasher detergents. 

Symptoms of a bad Rubber Washer in a dishwasher include:

• Visible signs of wear or damage to the washer, such as cracks, brittleness, or deformation.
• Water leaking from the dishwasher, particularly around areas where hoses and valves connect.
• A decrease in dishwasher performance due to water not being contained properly during cycles.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Delivers water from supply line to dishwasher tub. Replace if cracked, leaking, chewed by rodents, or damaged during installation or moving.

Fix continuous water flow or dishwasher overflow issues. This inlet valve controls water entering your dishwasher. Easy DIY repair with basic tools.

Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.

12 Ft in length

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Air Inlet is an OEM part for Whirlpool dishwashers. It draws in ambient room air to assist in drying dishes after wash cycles have been completed. With openings around its base, the air inlet facilitates airflow through the dish rack to evaporate residual moisture left on rinsed dishes.

Causes of a bad air inlet can include cracks in the plastic preventing proper draw of air currents, or obstructions blocking air pathways.

Symptoms of a bad air inlet include:

• Dishes remaining wet and not fully dried after cycles
• Puddles or watermarks left behind on upper racks and dishes
• Slow air movement detected near the bottom air vents
• Musty odors or smells developing inside the dishwasher

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Seals the float switch base to prevent leaks during dishwasher operation. Replace if water leaks from below the float assembly. Confirm fit with model.

Fix leaking dishwasher or water overflowing onto the floor. This float assembly rises with water level to prevent overfills. Easy 5-10 minute repair.

The Drain Pump is an OEM part for Whirlpool dishwashers. It is responsible for removing wastewater from the dishwasher tub during the drain cycle, ensuring that the dishwasher operates efficiently and effectively.

Causes of a bad drain pump can include clogging from food particles and debris, damage to the pump impeller, or electrical failures within the pump motor. Over time, regular use can lead to wear and tear that affects the pump's performance.

Symptoms of a bad drain pump include:

• Water not draining from the dishwasher
• Standing water at the bottom of the dishwasher after a cycle
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Leaking from the bottom or center of your dishwasher? The sump housing with included shaft seal often fixes this issue. DIY-friendly with video guide.

Seals the water inlet connection to prevent leaks where water enters the dishwasher tub. Replace if you notice moisture damage or leaking at the valve inlet.

Fix dishwasher leaks or rattling during drain cycle with this drain pump housing. Snaps into place—most DIYers complete this repair in minutes.