Maytag Dishwasher MDB9150AWS Leaking

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Inlet Valve is an OEM part for Whirlpool dishwashers. Located at the back of the dishwasher, this valve controls the flow of water into the dishwasher during wash cycles.

Causes of a bad water inlet valve can include mineral buildup accumulating inside the valve over many uses, wear and tear on the valve internals from constant opening and closing, or electronic component malfunctions.

Symptoms of a bad water inlet valve include:

• No water entering the dishwasher when starting cycles
• Water level issues where too much or too little water enters the tub
• A leak developing around the valve area or connection line

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This seal sits at the dishwasher's air/water inlet, creating a tight barrier where the inlet assembly meets the tub or door. Replacing a worn seal helps stop nuisance leaks and supports proper fill and venting performance. What it does

• Forms a watertight seal at the air/water inlet connection
• Helps prevent drips or seepage during fill and wash
• Supports correct venting to keep moisture contained inside the tub
• Common failure signs include water on the floor near the unit, dampness around the inlet/vent area, or a cracked, flattened, or brittle seal

• One air/water inlet seal

• Disconnect power and shut off water before servicing
• Access method varies by model; remove the inlet/vent cover or side panel to reach the seal
• Clean mating surfaces; seat the new seal evenly without distortion
• Reassemble and run a brief fill/wash to check for leaks

The Lower Washarm is an OEM replacement part for Whirlpool dishwashers. Positioned at the bottom of the dishwasher tub, it rotates during the wash cycle, distributing water and detergent evenly across the lower rack. 

Over time, wash arms can become clogged with food debris or mineral deposits, reducing water flow. Physical damage such as cracks or warping can also impede the wash arm's rotation and affect its cleaning performance.

Color: Gray

Symptoms of a faulty lower wash arm include:

• Inadequate cleaning of dishes on the lower rack
• Uneven or inconsistent water spray
• Clogged or obstructed spray nozzles
• The arm not spinning or rotating correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Includes: Upper and lower impellers, impeller screw with o-ring, motor shaft seal with install tool, and 3 o-rings needed to repair pump.

Upper

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose