Maytag Range MGR6772BDB Won't start or doesn't start

The Spark Module Kit is an OEM part for Whirlpool ranges. It is responsible for generating the spark needed to ignite the gas burners on the cooktop. The spark module sends electrical signals to the igniters, creating the spark that lights the gas for cooking. 

Over time, the spark module can fail due to electrical issues, exposure to moisture, or normal wear and tear. When the spark module becomes faulty, it can lead to various problems with igniting the burners.

Symptoms of a bad spark module include:

• Burners not lighting or taking a long time to light
• No clicking sound when turning the burner knob
• Burners only lighting intermittently
• Visible sparks or arcing from the module

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

NOTE: This part is only compatible with serial numbers starting with 21 and up on model 8351VV.

The Surface Burner Spark Electrode is an OEM part for Whirlpool gas ranges. This electrode is responsible for generating the spark that ignites the gas burner, allowing the burner to produce a flame for cooking.

Over time, the spark electrode can become faulty due to exposure to high temperatures, grease, and general wear and tear. This can lead to unreliable ignition or complete failure to ignite the burner.

Symptoms of a bad surface burner spark electrode include:

• The burner not igniting
• Weak or intermittent spark
• Clicking sound without ignition
• Burner flame going out soon after ignition

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation

This oven bake igniter lights the bake burner so your oven can reach and maintain temperature. A weak or failed igniter causes no heat in bake or very long preheat times. What it does:

• Heats and ignites the gas at the bake burner
• Draws the correct current to open the oven safety valve
• Helps restore normal preheat and consistent baking performance
• Common symptoms: no bake heat, igniter glows but burner won't light, long or incomplete preheat

• One bake igniter assembly

• Disconnect power and shut off gas supply before servicing
• Handle the igniter by the ceramic base; avoid touching the carbide element
• Transfer any mounting hardware from the original if needed and route wires away from heat
• Restore power/gas and test for proper ignition

This broil burner ignitor lights the broil flame in your oven for fast, even broiling. Replacing a weak or failed ignitor restores reliable ignition and consistent high-heat performance when starting broil. What it does

• Provides the ignition source for the oven's broil burner
• Works with the range's ignition system to light the broil flame
• Typical symptoms include the broiler not igniting or heating, intermittent lighting, or repeated ignition attempts without flame
• Visual clues of failure can include a cracked ceramic insulator, damaged tip, or burnt/frayed lead

• 1 broil burner ignitor assembly

• Disconnect power and shut off gas; allow the appliance to cool completely before service
• Access the broil burner at the top of the oven; remove any shields/panels and note the ignitor's original position and bracket orientation
• Handle the ceramic/tip carefully; avoid impact, route the lead away from hot surfaces, and make secure electrical connections
• Restore gas and power, then test broil to verify prompt ignition and a steady flame