Roper Trash compactor buttons not working: Common Causes & How to Fix

Repair Instructions:

Certain Roper trash compactor models utilize a door switch to check the position of the drawer. If this door switch is malfunctioning, the start button will be nonfunctional. To test if the door switch is working correctly, use a multimeter. This device can determine if the switch is opening and closing the electrical circuit as intended when the drawer is opened and shut. By using the multimeter to test the continuity of the switch, you can diagnose if the switch needs to be repaired or replaced to restore functionality to the start button.

How to Replace Trash Compactor Door Switch:

1. Safety Precautions:

   • To ensure safety, begin by unplugging the Roper trash compactor from the power source before starting the replacement process.
2. Empty the Compactor:
   • Remove any trash from the compactor drawer and ensure it's completely empty.
3. Access the Door Switch:
   • The door switch is typically located within the Roper trash compactor, often near the top of the compactor drawer.
4. Remove the Compactor Drawer:
   • To access the door switch, you may need to remove the compactor drawer. Most drawers have release mechanisms to facilitate removal.
5. Identify the Door Switch:
   • Within the compactor, identify the specific door switch that needs replacement.
6. Disconnect Wiring:
   • Carefully unplug or disconnect the wires from the old door switch, making a note of their positions.
7. Remove the Old Door Switch:
   • Typically, the door switch is secured by mounting screws or clips. Carefully detach it from these fasteners.
8. Replace with a New Door Switch:
   • Position the new door switch in the same location within the compactor, making sure it's properly aligned.
9. Secure the New Door Switch:
   • Reattach the mounting screws or clips to secure the new door switch in place. make sure they are tight.
10. Reinsert the Compactor Drawer:
    • Carefully reinsert the compactor drawer and make sure it locks securely in place.
11. Plug the Compactor Back In:
    • Reconnect the Roper trash compactor to the power source, making sure it's properly plugged in.
12. Test the Door Switch:
    • Open and close the compactor drawer to test the new door switch. Make sure it functions correctly and activates the compactor when the door is closed.
13. Final Checks:
    • Confirm that the Roper trash compactor operates as intended with the new door switch, providing the necessary safety features during use.

Repair Instructions:

The function controlled by a pushbutton switch depends on the specific appliance model. Use the wiring diagram for that model as a guide to testing the switch with a multimeter. Testing the switch determines if it is functioning correctly and making the proper electrical connections. If the pushbutton switch is unresponsive or multimeter testing indicates it is malfunctioning, replacement of the switch will be necessary. An improperly working pushbutton switch that fails to engage the appropriate electrical connections will not allow the appliance to carry out the intended function when the button is pressed.

How to Replace Trash Compactor Push Button Switch:

1. Safety Precautions:

   • Begin by unplugging the Roper trash compactor from the power source to ensure safety during the replacement process.
2. Empty the Compactor:
   • Remove any trash from the compactor drawer and make sure it's completely empty.
3. Access the Push Button Switch:
   • The push button switch is typically located on the control panel of the compactor.
4. Identify the Push Button Switch:
   • Examine the control panel to locate the push button switch that needs replacement.
5. Remove the Old Push Button Switch:
   • Carefully remove the old push button switch from its housing. This may involve unscrewing or unclipping it from the control panel.
6. Disconnect Wires:
   • Before completely removing the old switch, take note of the wire connections to ensure proper reconnection later. Carefully disconnect the wires.
7. Replace with a New Push Button Switch:
   • Position the new push button switch in the same location on the control panel, aligning it with the attachment points.
8. Reconnect Wires:
   • Reconnect the wires to the new push button switch, ensuring they are connected in the same configuration as the old switch.
9. Secure the New Push Button Switch:
   • Reattach the switch to the control panel using the appropriate screws, bolts, or clips to secure it in place.
10. Plug the Compactor Back In:
    • Reconnect the Roper trash compactor to the power source, ensuring it's properly plugged in.
11. Test the Push Button Switch:
    • Operate the Roper trash compactor to confirm that the new push button switch functions correctly, allowing you to control the compactor's operation.
12. Final Checks:
    • Make sure that the Roper trash compactor's push button switch works properly, facilitating convenient and efficient operation.

Repair Instructions:

The selector switch activates diverse functions depending on the appliance model. Use the wiring diagram for that specific model as a guide for testing the selector switch with a multimeter. This testing verifies if the switch is working correctly and properly connecting the electrical circuits. If the selector switch is unresponsive or multimeter testing reveals it is defective, the switch will need replacement.

How to Replace Trash Compactor Selector Switch:

1. Safety Precautions:

   • Begin by unplugging the Roper trash compactor from the power source to ensure safety during the replacement process.
2. Empty the Compactor:
   • Remove any trash from the compactor drawer and make sure it's completely empty.
3. Locate the Selector Switch:
   • The selector switch is typically found on the control panel of the Roper trash compactor, often integrated with other control buttons.
4. Remove the Control Panel Cover:
   • To access the selector switch, you may need to remove the control panel cover. This usually involves unscrewing or unclipping the cover.
5. Identify the Selector Switch:
   • Within the control panel, identify the specific selector switch that needs replacement.
6. Disconnect Wiring:
   • Carefully unplug or disconnect the wires from the old selector switch, taking note of their positions.
7. Remove the Old Selector Switch:
   • The selector switch is usually secured with mounting screws or clips. Carefully detach it from these fasteners.
8. Replace with a New Selector Switch:
   • Position the new selector switch in the same location within the control panel, making sure it's properly aligned.
9. Secure the New Selector Switch:
   • Reattach the mounting screws or clips to secure the new selector switch in place. make sure they are tight.
10. Reassemble the Control Panel:
    • Reattach the control panel cover, securing it with screws or clips.
11. Plug the Compactor Back In:
    • Reconnect the Roper trash compactor to the power source, making sure it's properly plugged in.
12. Test the Compactor Operation:
    • Power on the compactor and use the new selector switch to make sure it functions correctly, allowing you to select different compactor settings.
13. Final Checks:
    • Confirm that the Roper trash compactor operates as intended with the new selector switch, enabling you to choose different compaction options.

Repair Instructions:

If the buttons on the Roper trash compactor are unresponsive, debris accumulation or fallen objects behind the drawer could be preventing it from fully closing. This can stop the drawer from activating the door switch. To address this issue, pull out the drawer completely and inspect for any obstructions that are blocking the drawer from shutting entirely. Remove any trash buildup or fallen items from behind the drawer allowing it to close completely.