Whirlpool Dishwasher DU8570XT2 Leaking

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drain & Wash Impeller Kit is an OEM part for Whirlpool dishwashers. This kit includes components critical for the efficient movement of water within the dishwasher, both for washing the dishes and draining the water at the end of the cycle. The impeller aids in creating the necessary water pressure to clean dishes effectively and ensures that water is properly expelled from the dishwasher.

Symptoms of a failing Drain & Wash Impeller Kit include:

• Dishes not being cleaned thoroughly
• Water not draining properly from the dishwasher, leaving standing water
• Unusual noises during the wash or drain cycles, such as grinding or humming
• The dishwasher cycle taking longer than usual or not completing
• Visible damage or wear to the impeller components

Causes of a bad impeller kit can include normal wear and tear from regular use, blockages or debris that damage the impeller blades, or issues with the motor that affect impeller performance.

This OEM part is also compatible with some models from brands such as Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore. 

This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:

• Seals the joint at the pump outlet to prevent water leakage
• Helps maintain proper circulation by keeping the pump discharge airtight/watertight
• Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal

• 1 pump outlet seal

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
• Note seal orientation; clean mating surfaces before installing the new seal
• Seat the seal evenly; reassemble and run a short test to check for leaks

This seal kit is for the main tub. It goes around the pump housing.

Kit includes rubber rings, impeller screw with seal and fiber gasket.

The Check Valve Assembly is an OEM replacement part for Whirlpool dishwashers. It is a component that regulates water flow and pressure, allowing water to enter the dishwasher during designated cycles but preventing backflow. The check valve plays an important role in the overall water distribution system of the dishwasher. 

Causes of a bad check valve can include mineral buildup blocking the valve ports over time, damage to the valve mechanism or seals, or decreased valve integrity from wear and repeated use. 

Symptoms of a bad check valve include:

• Leaks or water not properly entering the dishwasher 
• Incomplete or inefficient washing and rinsing cycles
• Strange sounds coming from the water inlet area
• Higher water usage due to faulty draining 

Note: O-ring included.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rubber Washer is an OEM part for Whirlpool dishwashers. This washer plays a role in ensuring a leak-proof seal at various connection points within the dishwasher, such as at the water inlet valve or hose connections. Its primary function is to prevent water from leaking out of the dishwasher during operation, thereby ensuring efficient and safe use of the appliance. 

Over time, rubber washers can deteriorate due to the constant exposure to water and chemicals found in dishwasher detergents. 

Symptoms of a bad Rubber Washer in a dishwasher include:

• Visible signs of wear or damage to the washer, such as cracks, brittleness, or deformation.
• Water leaking from the dishwasher, particularly around areas where hoses and valves connect.
• A decrease in dishwasher performance due to water not being contained properly during cycles.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Cap with rubber pressure seal to hold down lower spray arm. Instruction sheet included.