Whirlpool Washer LSN3000PG3 Leaking

Washer leaking water underneath or not draining? This drain pump removes water during the cycle. DIY repair typically takes 10-15 minutes with basic tools.

Drain hose routes wastewater from your washer tub to household plumbing. Replace if cracked, leaking, worn through, or damaged from wear or friction.

Seals the center post/agitator shaft to prevent water leaks during wash cycles. Replace if you notice pooling water under your washer. Confirm fit with your model.

Replacement drain hose connecting washer tub to pump assembly. Replace if cracked, split, leaking, or worn. Carries water from tub during drain cycle.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Washer not filling with water? A faulty water inlet valve is often the cause. This assembly controls water flow during fill cycles. DIY repair in 15 minutes.

Washer slowly filling or dripping when off? A faulty vacuum break allows water to siphon back into the drum. Takes 30 minutes with our video guide.

Connects the vacuum break to the outer tub in your washer. Replace if cracked, split, or leaking to prevent water from bypassing the tub during fills.

Prevents water leaks around the transmission shaft in your washer. Replace if you notice water on the floor or oil seepage. Confirm fit with your model.

Maintains watertight seal between outer tub and tub ring, preventing leaks during wash and spin cycles. Replace if leaking from top of drum or spin issues.

The Shaft Seal is an OEM part for Whirlpool washing machines. This seal is designed to fit around the shaft that connects the tub to the transmission or motor, preventing water from leaking out of the tub and into the machine's internal components.

Causes of damage to the Shaft Seal often involve normal wear and tear from regular use, as the constant motion of the shaft can gradually degrade the seal.

Symptoms of a bad Shaft Seal include:

• Water leaking from the underside of the washing machine, particularly during or after a wash cycle
• A noisy operation, especially during the spin cycle, can sometimes result from water leaking into the bearings and causing them to fail
• The presence of rust or corrosion around the area where the shaft enters the tub

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Prevents oil leaks from your washer's gearcase and keeps internal components lubricated. Replace if you notice oil pooling under the machine.

Replace your washer's cracked or leaking outer tub. This housing holds the inner basket and prevents water from leaking into the machine's interior.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.

Bearing and seal kit for washers. Replace when you hear grinding, thumping, or banging noises during spin cycles. Includes bearings and seals for shaft.

Prevents water leaks between washer cover and tub during wash cycles. Replace if leaking or water escapes during washing. Verify fit with model number.