Dryer Bottom Drawer Panel Parts

Plastic door cover

This water tank assembly collects condensation produced during the drying cycle in a ventless or condenser dryer. It is a removable reservoir that must be emptied periodically to allow the dryer to continue operating. Replace this tank if it is cracked, leaking, or if the dryer displays a full tank error even after emptying.

This is the trim ring that fits around the inside of the dryer door opening, providing a finished edge and helping secure the door seal. It creates a smooth transition between the door and the drum area while helping maintain a proper seal during operation. Replace this trim ring if it is cracked, warped, or broken, which can cause air leaks that reduce drying efficiency or allow lint to escape.

This is the top work surface panel that covers the upper portion of the dryer cabinet. It provides structural support and a finished exterior surface while protecting internal components from dust and debris. Replace this panel if it is dented, cracked, rusted, or if the finish is damaged.

Replacement control panel console for laundry center front assembly. Restores appearance and provides mounting surface for user controls. Replaces cracked, faded, or damaged console.

Control panel for dryers and laundry centers. Replaces cracked, broken, or damaged panels on the front of your unit. Restores appearance and function.

Control panel for dryers. Installs on the front of the unit housing the display and buttons. Replace if cracked, damaged, or faded from wear and age.

This white top panel replaces the outer cooktop surface on compatible ranges to restore a finished look and protect internal components from spills and debris. It's a direct-fit exterior part used when the original top is dented, cracked, or cosmetically worn. What it does:

• Covers and protects the range's internal components and burners from spills and heat exposure
• Restores a clean, finished appearance to the appliance exterior
• Helps maintain proper spacing and support for burner assemblies and controls
• Reduces risk of debris falling into the cabinet area below the cooktop

• One white top panel

• Requires basic disassembly of the cooktop; your model's service manual for step-by-step instructions
• Disconnect power (and gas supply if applicable) before beginning any repair to avoid shock or injury
• Use appropriate fasteners and gaskets from your model's parts list; do not force-fit parts

Outer cabinet cover panel for dryer exterior. Replaces dented, cracked, or damaged panels. Restores appearance and protects internal components.

This is the top plate assembly that forms the upper exterior surface of the dryer. It provides structural support and a finished appearance to the top of the unit. Replace this panel if it is dented, scratched, rusted, or warped, or if the mounting tabs are broken and the panel no longer sits securely.

This is the replacement body frame that secures and finishes the appliance front, restoring proper alignment and appearance. It provides a rigid mounting surface for the front panel and helps keep internal components protected from dust and debris. What it does

• Replaces a cracked, warped, or damaged front frame that causes gaps or poor fit
• Restores correct alignment of the front panel and door openings
• Covers and protects cabinet edges and mounting points from wear
• Helps prevent rattles and vibration by providing a stable mounting surface

• Frame/body replacement part

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove the front panel or door assembly per the service manual to access mounting screws
• Handle edges carefully; use proper tools and keep fasteners organized for reassembly

This rear panel replaces the back cabinet cover on compatible Whirlpool dryers, protecting internal components and helping direct vent airflow. It restores a secure, finished exterior and keeps wiring and controls shielded. What it does:

• Covers and protects the dryer's internal components at the rear, including wiring and control assemblies
• Helps maintain proper venting path and airflow by providing the correct rear opening and mounting surface
• Prevents debris, pets, and accidental contact with internal parts
• Stops rattling or flexing caused by a bent or damaged back panel

• Disconnect power (and gas supply on gas models) before starting any repair
• Remove the dryer from the wall and disconnect the vent to access and replace the rear panel
• Use appropriate hand tools to remove and reinstall mounting screws; retain hardware if reusing
• Handle edges carefully to avoid cuts; secure all fasteners before returning dryer to service

This is the lower access panel, also called a toe panel, that attaches to the front bottom of the washer. It covers the internal components beneath the drum area and provides a finished appearance. Replace this panel if it is dented, cracked, rusted, or if the mounting tabs are broken, leaving the lower portion of the machine exposed.