Range Hood Slow Clamp Snowblower Spark Plug Parts

This fan clip secures the ventilation fan blade or blower wheel to the motor shaft, preventing looseness and vibration. Replacing a worn or missing clip restores a tight fit so the fan runs smoothly and maintains proper airflow.

• Holds the fan blade/blower wheel firmly on the motor shaft
• Helps reduce wobble, scraping, or rattling noises during fan operation
• Can resolve a loose or non-spinning fan caused by a failed/missing retainer
• Supports proper airflow and cooling performance

• Disconnect power and allow the appliance to cool before servicing
• Access the fan/blower assembly and note the original clip's orientation
• Seat the clip fully in the shaft groove; ensure the wheel is secure and spins freely
• Wear cut-resistant gloves and use caution around sharp metal edges

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

This is a filter latch that secures the refrigerator water/air filter housing so the filter stays seated and the housing seals correctly. Replaces a worn or broken latch to restore proper filter retention. What it does:

• Holds the filter housing cover or cartridge firmly in place to prevent dislodging
• Helps maintain a proper seal to reduce leaks or bypass around the filter
• Stops the filter from falling out when removing or replacing the cartridge
• Resolves symptoms like a loose or broken latch, filter not staying seated, or water bypass near the filter area

• Disconnect power and shut off water supply before servicing the filter area
• Remove the old latch per your model's service instructions; small hand tools may be needed
• Inspect surrounding housing for damage; replace housing if cracked or warped
• Do not force or overtighten; seat the latch so the filter seals correctly

This clip secures the upper dishwasher rack to its sliding assembly so the rack stays properly aligned and rides smoothly. A small but essential part for restoring stable upper-rack operation and preventing sideways wobble. What it does

• Holds the top/upper rack in place on the track or rail assembly
• Prevents the rack from shifting, sagging, or detaching when loading or pulling out the rack
• Restores correct rack alignment to help dishes load and wash evenly
• Simple replacement for common rack-tilt or rack-drop symptoms

• One replacement rack top clip

• Basic hand tools may be required; inspect surrounding components for related wear
• Remove power to the appliance and follow manufacturer safety guidance before servicing
• If the clip is brittle or broken, replace matching clips on the same rack for even support

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

This water filter latch secures the refrigerator's filter housing so the cartridge stays in place and seals correctly. It restores proper filter engagement to help prevent leaks and ensure consistent water dispensing. What it does:

• Secures the water filter cartridge in the housing so the filter locks into place
• Helps maintain a proper seal to reduce the risk of water leaks
• Prevents the filter from becoming loose or falling out during normal use
• Can resolve symptoms like a loose filter, leaking at the filter area, or poor dispenser performance

• Turn off the water supply and remove the filter cartridge before servicing
• Handle plastic parts gently to avoid cracking; confirm the latch seats fully in the housing
• Do not use the appliance if water leaks persist after replacement

This retainer is a small mounting clip used in Broan ventilation hoods to hold trim, lenses, or small assemblies securely in place. Replacing a worn or broken retainer restores stable mounting and reduces vibration or rattling. What it does:

• Secures trim pieces, light lenses, or small assemblies so they stay aligned and seated
• Prevents parts from shifting or vibrating during operation
• Helps stop rattling or loose components around the hood opening
• Keeps replaceable covers and lenses from falling out when installed correctly

• Disconnect power to the appliance or turn the circuit breaker off before working on the hood
• Use common hand tools as needed; handle sharp sheet-metal edges with gloves
• Verify this retainer matches the damaged piece before installation

This is a filter clip used on range hoods. It is sometimes referred to as a range hood clip or range hood clamp. There is a filter located inside the range hood that is used to filter out smells and small particles during the cooking process. The filter is held in place by the filter clip. Accidental damage, wear and tear, or misuse may cause the filter clip to fall out or no longer be capable of holding the filter. If the filter clip is missing or broken, a replacement part is required.A visual inspection will determine if the filter clip is damaged or missing. Replacing the clip filter is an easy process. Remove the old filter clip if there is one present. Line up the new filter clip in the same position and snap it into place. Wear gloves for protection. There are no special tools required to make this repair.This is an authentic OEM replacement part. It is sold as an individual unit. The filter clip is made of durable, high-quality materials. The replacement part can be installed in several different models of range appliances. It is compatible with machines produced by General Electric, Hotpoint, and RCA.