1106691269166912 Parts

This harness clip secures appliance wiring to the cabinet or components to prevent rubbing, pinching, and interference with moving parts. It keeps wiring routed neatly for reliable operation and reduced risk of abrasion-related failures. What it does:

• Holds wire harnesses in place to prevent chafing against sharp edges or moving parts
• Reduces vibration-related noise and intermittent connections caused by loose wiring
• Helps maintain proper wire routing around panels, motors, and heaters
• Supports safe operation by keeping wires away from heat sources and pinch points

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove panels or access covers as needed to reach the original clip location
• Install by snapping or seating the clip into the original mounting point and securing the harness in the retainer; replace any broken mounts
• Inspect surrounding wiring and replace damaged wires or insulation before completing repair

This 3-cycle timer controls cycle advancement and timing in dryer systems, restoring normal sequencing and timed functions. Replaces a worn or stuck timer to help the dryer move through timed, automatic, and end-of-cycle positions. What it does:

• Advances dryer cycles and routes power to motors, heat, and other timed functions
• Causes the dryer to stop at the correct cycle positions when working properly
• Common symptoms: cycles won't advance, timer knob stuck or loose, dryer doesn't complete timed cycles
• Works as the central timing switch that sequences heat and motor circuits

• Disconnect power before servicing to avoid shock hazard
• Use the dryer's tech sheet/installation diagram for correct wire routing and connector placement
• Verify electrical connections and test continuity with a meter before reassembly

This blower housing directs dryer airflow from the drum to the exhaust for proper ventilation and consistent drying performance. It replaces a cracked or damaged housing to restore airflow and reduce noise. What it does:

• Channels heated air from the drum to the exhaust vent to maintain drying efficiency
• Helps support the blower wheel and keeps the wheel aligned for smooth operation
• Commonly replaced for reduced airflow, longer dry times, or unusual noise from the rear of the dryer
• Can prevent overheating caused by restricted or leaking airflow

• Disconnect power (and gas supply if applicable) before beginning repair
• Handle edges carefully; wear gloves to avoid cuts and protect the blower wheel
• Reassemble panels and test dryer on a short cycle to confirm airflow and quiet operation

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

A replacement incandescent lamp that restores oven cavity lighting so you can check cooking progress without opening the door. Fits the OEM light socket and provides bright, direct illumination for safe food monitoring. What it does:

• Replaces a burned-out oven/incandescent light so the interior is lit during use
• Helps you see food clearly to prevent overcooking or missed doneness
• Restores normal light operation when the oven lamp no longer powers on or flickers
• Works with the oven light assembly and standard appliance light sockets

• Disconnect power or unplug the appliance before replacing the bulb to avoid shock
• Allow the old bulb and oven interior to cool before handling
• Use a cloth or gloves to install the bulb to avoid skin oils on the glass
• If the new bulb still does not light, check the socket and replace switches or wiring only after proper diagnosis

A front toe panel assembly that restores the lower front trim and airflow opening on compatible laundry appliances. Replaces a damaged or missing lower access panel to keep the cabinet sealed and looking finished. What it does:

• Covers the lower front of the appliance cabinet, protecting internal components from debris.
• Restores the lower air or vent opening and directs airflow as intended.
• Prevents items from falling under the appliance and reduces drafts at the base.
• Helps maintain proper appearance and fit of the appliance front.

• Disconnect power (and gas if applicable) before starting any work.
• Install requires removing the appliance kick strip or lower access fasteners; retain hardware as needed.
• Align panel tabs/clips with cabinet slots and secure with the original screws or clips.
• Replace any damaged clips or mounting hardware to ensure a secure fit.

Size: 6 - 20 x 1 1/16 inch.

This drum baffle restores proper tumbling by lifting and separating laundry as the dryer drum rotates. It helps improve drying performance and reduces garment bunching. What it does:

• Lifts and tumbles clothes so air flows more evenly through the load
• Helps prevent garments from clumping or wrapping around the drum
• Can reduce rubbing, thumping, or scraping noises caused by a loose or damaged lifter
• Restores consistent drum contact and improves drying efficiency

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires opening the dryer cabinet or front panel; small tools may be needed
• Align the baffle with factory mounting holes and secure with existing fasteners; use correct screws if replacements are required
• Inspect and replace worn drum or support parts as needed for reliable operation

The Door Seal is an OEM component specifically designed for Whirlpool dryers. It works to create an airtight seal between the dryer door opening and drum interior. During operation, heated air and moisture are contained within the drum thanks to this crucial seal. 

Symptoms of a worn door seal include:

• Increased drying time due to air leaks
• Clothes not drying completely before end of cycle  
• Excess humidity escaping into home
• Discoloration or residue buildup on door glass

Causes of failure are normal wear and compression over extended use, or damage from improper door closure. A worn seal degrades efficiency and performance of the dryer.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This bulkhead is the front interior panel that supports the drum and helps direct dryer airflow for efficient tumbling and exhaust. It restores proper drum alignment and airflow when the original panel is worn or damaged. What it does:

• Provides a stable mounting surface for the drum and front bearing/glide assembly
• Helps channel air from the drum to the exhaust path for consistent drying
• Prevents drum wobble and rubbing that can cause noise or fabric wear
• Reduces air leaks and hot spots that can extend dry times or trigger heat issues

• One bulkhead panel

• Disconnect power and venting before beginning any repair
• Removing the front panel and drum is typically required to access and replace the bulkhead
• Inspect drum seals, rollers, and bearings while the dryer is open; replace any worn components
• Use appropriate tools and follow OEM instructions.

This multi-vent plug seals an unused vent opening to stop unwanted airflow and keep the appliance interior protected. It's a direct-fit replacement designed to restore proper venting and help prevent drafts, debris, and pests. What it does:

• Plugs an unused multi-vent opening to prevent air leakage and drafts
• Helps keep dust, lint, and small debris out of the appliance vent path
• Reduces the chance of pest entry through an open vent
• Restores the intended vent configuration after service or part removal

• Disconnect power or gas to the appliance before servicing for safety
• Install by aligning and pressing the plug firmly into the vent opening until seated
• Do not force if resistance is excessive; inspect for obstructions or damage
• Replace damaged parts before installing the plug

This heater box is the protective housing that encloses and supports the heating element in your appliance. Replacing a warped or damaged housing helps restore safe, efficient heating and protects nearby components from excessive heat.

• Holds the heater element securely and maintains proper spacing from surrounding parts
• Shields adjacent wiring and components from direct heat
• Helps maintain consistent heating performance when the original housing is heat-damaged or cracked
• Common symptoms include visible melting/warping, loose element fitment, burning odors, or repeated safety shutoffs

• Disconnect power (and gas supply, if applicable) and allow the unit to cool completely before service
• Take photos of the existing layout to aid reassembly and wire routing
• Transfer the heater element and any model-specific hardware to the new housing in the same orientation
• Ensure wiring is clear of sharp edges and heat sources; reassemble and test for proper operation

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components