11069133141 Parts

Replacement mounting nut secures panels, brackets, and studs in dryers. Restores tight fit for worn, stripped, or missing fastening hardware.

This small nozzle directs the water stream cleanly into the ice maker during the fill cycle, helping prevent splashing and leaks so your unit produces consistent, properly sized ice cubes.

• Channels water from the fill tube into the ice maker's fill cup/mold
• Helps maintain correct fill volume and cube formation
• Reduces stray spray that can cause frost or ice buildup
• Typical symptoms: dripping from the fill tube, ice clumps below the ice maker, hollow/small cubes, or water on the freezer shelf

• Disconnect power and shut off the water supply before servicing
• Access the fill tube/ice maker area and remove the old nozzle
• Match the original orientation and seat the new nozzle fully
• Restore water and power, then run a fill cycle and check for leaks

Dryer won't start or control panel not responding? This electronic control board manages cycle selection and timing. Restores responsive controls.

Secures the heater housing to the dryer cabinet. Replace if your bracket is bent, cracked, or missing to restore stable mounting and alignment.

Screw: 8-16 x 3/8 inch.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This is the outer grille cover that sits over the lint screen area on the front of the dryer. It provides airflow while protecting the lint filter slot from debris and damage. Replace this part if it is cracked, broken, or has missing louvers that allow lint to escape or reduce drying efficiency.

Dryer won't heat or flames are yellow? This butane burner orifice meters gas flow for clean, reliable ignition. Required for butane conversions.

Trim ring that finishes the control opening on your dryer. Replace if the original bezel is cracked, broken, or missing to restore a clean look.

Replace your dryer door seal to restore a tight gasket and prevent air leaks. If your seal is cracked, torn, or worn, this part ensures secure closure. Confirm fit with your model number.

Flat metal washer that distributes load and secures fasteners in your dryer. Replace if worn, corroded, or missing to restore proper fastener grip.

Wire harness for dryers and laundry centers. Connects electrical components inside the cabinet. Replace if wires are frayed, damaged, or burnt.

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

Fix a dryer that won't heat or has a weak flame with this gas burner orifice. Controls proper fuel flow for consistent heating. Direct replacement part.

Covers and seals your dryer's exhaust opening to direct airflow and keep debris out. Replace if cracked, warped, or missing to maintain proper venting.

The Housing is an OEM component specifically designed for Whirlpool electric dryers. Found within the rear upper compartment, the square blower housing surrounds and supports the centrifugal fan assembly. 

Machined from durable heavy-duty plastic with ventilation slots, the blower housing channels airflow from the fan into the dual-duct exhaust system. Strategically placed mounting tabs secure the assembly in precise alignment.

Causes of a bad blower housing include cracks developing from years of constant vibration stress. Heat and exhaust moisture exposure could also warp or degrade housing material properties over time.

Symptoms of a bad housing include:  

• Noisy or unbalanced fan operation
• Reduced air velocity through ducts 
• Faulty directional airflow inside the dryer drum

Compatible with Whirlpool, Maytag, KitchenAid, and some high-efficiency Kenmore models.