11069133141 Parts

Dryer not heating evenly or taking too long to dry? A cracked or missing air duct disrupts airflow. This duct restores proper circulation and drying.

Complete dryer door assembly with view glass window. Replace your cracked, broken, or damaged door to restore proper drum access and secure closure.

Dryer won't heat or flames are yellow? This butane burner orifice meters gas flow for clean, reliable ignition. Required for butane conversions.

This is the outer grille cover that sits over the lint screen area on the front of the dryer. It provides airflow while protecting the lint filter slot from debris and damage. Replace this part if it is cracked, broken, or has missing louvers that allow lint to escape or reduce drying efficiency.

Trim ring that finishes the control opening on your dryer. Replace if the original bezel is cracked, broken, or missing to restore a clean look.

Fix a sagging or broken dryer door with this heavy-duty metal hinge. Secures the door panel for smooth opening and closing. Simple 7-minute repair.

Fix a sagging or broken dryer door with this heavy-duty metal hinge. Holds the door securely through thousands of cycles. Simple DIY repair in minutes.

This LP gas conversion orifice adjusts gas flow for compatible gas ranges and cooktops when converting from natural gas to liquid propane, helping the appliance run safely and correctly after conversion. What it does:

• Replaces the burner orifice to reduce gas flow for LP fuel pressure and correct flame size
• Helps restore consistent, stable burner flames after an authorized LP conversion
• Addresses symptoms like unusually large or yellow flames, poor ignition, or unstable burner performance after conversion
• Works with the appliance's existing valve and burner components as part of a proper conversion

• Follow the appliance manufacturer's LP conversion instructions and parts list exactly
• Turn off gas supply and disconnect power before servicing
• Use correct torque and fittings; do not force or cross-thread the orifice
• Always perform an approved gas leak test and check burner flames after installation

Covers and seals your dryer's exhaust opening to direct airflow and keep debris out. Replace if cracked, warped, or missing to maintain proper venting.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

The Valve is an OEM component specifically designed for Whirlpool gas and electric dryers. It controls the flow of gas to the burner and maintains proper temperature during the drying cycle. The valve is opened and closed electronically based on temperature and dryness sensor readings.

Symptoms of a bad dryer valve include:

• Inability to achieve or maintain high enough heat for efficient drying  
• Fluctuating temperatures throughout cycles
• Repeated drying times or inability to fully dry loads
• Burner or heating element issues 

Causes of a dryer valve malfunctioning can be worn over many years of use. Dust or debris accumulation in the valve mechanism is also common.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Replacement mounting nut for dryers. Secures panels, brackets, and assemblies. Replace if stripped, missing, or corroded during repairs or maintenance.

Replaces worn or damaged lower cabinet base that supports your dryer frame. Needed when the original base is cracked, broken, or missing. Restores stability.

Replacement mounting screw for securing panels, brackets, and interior assemblies. Needed when original screw is stripped, missing, or damaged.

Structural inner panel that supports the dryer tub and provides mounting for controls and seals. Replace if cracked or damaged to prevent leaks. Verify fit.