110C26832692 Parts

This bulkhead is the front tub bulkhead that channels water between the dishwasher tub and control/door area, helping maintain proper flow and prevent leaks. It replaces a cracked or warped front bulkhead to restore sealing and alignment. What it does:

• Forms the sealed interface between the tub and door/control area to prevent water leakage
• Directs water flow from the tub toward the drain and pump assembly
• Restores proper fit and alignment when the original bulkhead is cracked, warped, or damaged
• Helps maintain wash performance by preserving the dishwasher's internal water path

• 1 bulkhead assembly (single piece as shown)

• Disconnect power and water supply before starting any repair
• Remove the dishwasher door and inner components as needed to access and replace the bulkhead
• Inspect adjoining gaskets, seals, and mounting hardware; replace any damaged parts to ensure a watertight fit

This housing slot heater melts ice and prevents frost buildup inside the appliance housing, helping restore normal airflow and component operation. It's a direct replacement heater element used where ice forms around the housing slot. What it does:

• Provides targeted heat to the housing slot to reduce ice accumulation
• Helps restore proper airflow and circulation by clearing frost/ice blockages
• Commonly replaced when the housing develops repeated ice buildup or intermittent heating
• Works as part of the defrost/anti-ice system to protect internal components

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing exterior panels or trim; keep fasteners organized
• Handle the heater element and wiring with care to avoid damage to the element or connector

This front axial bulkhead is the front support assembly that centers the dryer drum and provides a mounting surface for the front bearing and seal. It restores proper drum alignment and helps reduce noise and rubbing. What it does:

• Supports and centers the dryer drum at the front to maintain smooth rotation
• Houses the front bearing/seal interface to prevent rubbing and reduce vibration
• Stops or reduces scraping, grinding, wobbling, or uneven drum movement
• Restores proper drum alignment when the original bulkhead is cracked, warped, or worn

• Disconnect power (and gas, if applicable) before starting any repair
• Remove the dryer front panel and drum to access bulkhead mounting fasteners
• Inspect and replace any associated bearings, seals, or mounting hardware as needed
• Reassemble carefully and test on a short cycle to ensure drum spins smoothly and quietly

This wire harness assembly routes power and control signals between components so the appliance operates reliably. It replaces a damaged or worn harness to restore proper electrical connections and reduce intermittent faults. What it does:

• Provides the main connector wiring between electrical components and the control board.
• Restores lost power or control signals caused by broken, frayed, or burnt wires.
• Helps stop intermittent operation, control errors, or components that won't power on.
• Maintains secure connector fit and correct wire routing to prevent shorting.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Handle connectors carefully; release locking tabs to avoid damage.
• Route and secure the harness following original wire paths and clips to prevent chafing.

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.

This drying rack is a flat drum accessory that lets delicate or non-tumble items dry safely without spinning, so sweaters, shoes and other fragile pieces keep their shape and avoid wear from tumbling. What it does:

• Holds items flat inside the dryer so they dry without tumbling or twisting
• Lets you dry shoes, sweaters, stuffed toys and other delicate items safely
• Helps prevent stretching, snagging or damage caused by regular drum rotation
• Works with dryer cycles designed for air-dry or no-tumble drying

• One drying rack

• Place the rack flat inside the dryer drum before starting a no-tumble or air-dry cycle
• Ensure the rack is centered and lays flat to avoid contact with the dryer's door or vent
• Do not use with heavy, unbalanced loads or cycles designed for high-speed tumbling

This is a replacement 8-18 x 7/32 machine screw used to secure panels and small components in compatible Whirlpool appliances. It restores proper fastening where a screw is missing, stripped, or damaged. What it does:

• Secures panels, trim pieces, brackets or small components to prevent movement
• Helps stop rattling, vibration noise, or loose-fitting parts
• Replaces missing or damaged screws to restore proper alignment of panels or controls
• Used wherever an 8-18 x 7/32 machine screw is specified by the manufacturer

• Unplug the appliance or turn off power before servicing.
• Use the correct screwdriver or bit to avoid stripping the head; tighten snugly but do not over-torque.
• Replace any stripped inserts or mating hardware if threads are damaged.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This exhaust vent extension restores proper exhaust airflow by lengthening or adapting the appliance exhaust outlet to the vent duct. It helps maintain safe ventilation and reduces backpressure that can cause poor performance or odors. What it does:

• Extends or adapts the appliance exhaust outlet to reach the home vent duct
• Directs exhaust airflow to reduce backflow and help prevent overheating
• Helps resolve symptoms like weak venting, lingering odors, or unusual appliance cycling
• Provides a stable connection point for the exhaust duct to improve sealing and airflow

• Turn off and disconnect power (and gas if applicable) to the appliance before installing.
• Use proper fasteners and high-temperature-rated duct tape or clamps as recommended by the appliance manufacturer.

This is a replacement mounting nut that secures appliance components and helps keep panels, assemblies and fasteners tight for stable operation. A simple, OEM-fit nut for repair or maintenance. What it does

• Fastens and secures assemblies, brackets or panels to prevent loosening during use
• Helps reduce vibration and rattling caused by loose hardware
• Restores proper component alignment when a stripped or missing nut causes movement
• Fits in the same location and function as the original factory nut

• Inspect the mating bolt/stud and threads; replace damaged hardware before installing the nut
• Tighten to the appliance manufacturer's specified torque where available; avoid over-tightening
• Use hand tools appropriate for the nut size to prevent rounding the hex
• Disconnect power or follow manufacturer safety instructions before servicing electrical appliances