16593201 Parts

This replacement part is a stud, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Studs are typically found in or around the carburetor in many lawn mowers. These studs hold specific parts in place and keep the engine running smoothly and efficiently. A new stud might be needed if the user notices that different parts of the carburetor are loose or even missing. It is possible that the previous studs become stripped or worn down over time due to normal wear and tear. It's possible that the stud can become stuck as well, and the user might need pliers to retrieve and replace it with a new part. This replacement part is sold individually and is a genuine OEM part sourced directly from the manufacturer. Be sure to purchase the correct amount of studs as many machines require more than one for proper operations.

M6 x 1 flange bolt for outdoor power equipment. Secures engine covers, handles, and components. Replace if stripped, rusted, or missing threads.

Fixes engine misfires and rough running caused by improper valve clearance. This adjusting nut helps restore correct valve timing on lawn mowers and tillers.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

Replace a leaking or damaged oil drain assembly on your snowblower engine. Includes valve for easier oil changes. Basic hand tools required.

Ignition coil assembly for snow throwers and lawn engines. Installs on the engine block. Replace if your original coil is cracked, broken, or detached.

Engine losing power or running rough? A worn cylinder head assembly often causes reduced efficiency. This part covers the cylinder and houses valves.

Replacement flywheel for small engines. This rotating wheel component stores rotational energy. Order a new one if yours is cracked, rusted, or damaged.

Replacement muffler assembly for gas snowblowers and lawn engines. Installs on exhaust system. Order if your original is rusted, cracked, or damaged.

Crankcase cover for small engines. Protects internal components from debris and damage. Replace if cracked, broken, or missing to maintain proper engine protection.

Seals carburetor to insulator plate, preventing fuel leaks. Replace when worn, cracked, or torn to restore engine efficiency. Verify fit with your model.

Engine won't start or runs rough? This camshaft assembly converts rotational motion to reciprocal motion for proper engine operation. Moderate DIY repair.

This is an MTD rocker arm. The rocker arm works in conjunction with the engine and head. The job of the rocker arm is to push the intake valve open, allowing fuel and air to enter the cylinder. Since the rocker arm is a part of the head gasket system, any damage can cause the engine to run extremely weak. There could also be a noticeable clicking or ticking noise originating from the engine area of the mower. A visual inspection of the rocker arm will confirm any damage. Begin the repair by removing the muffler guard. After removal, move to the valve cover and remove that guard as well. Disconnect the fuel and air lines running to the head. Remove the spark plugs in the valve section. Finally, the rocker arm can be removed using a socket wrench. Repeat these steps in reverse to install the new rocker arm.This product is sourced directly from the manufacturer as a genuine OEM part. The component is available individually, separate from the original machine. This part is compatible with MTD and Cub Cadet brand equipment.

Seals the intake valve to prevent oil leaks and maintain proper compression in small engines. Replace if you notice oil consumption or performance loss.

Engine cylinder head gasket seals the combustion chamber. Replace if you notice oil leaks, overheating, or loss of compression. Confirm fit with your model.

Replaces a worn, damaged, or missing valve spring retainer in your outdoor power equipment engine. Essential small fastener component for valve assembly.