2198608 2317277 Parts

The washer seal is an essential part of the carburetor float bowl on engines with carburetors on lawn mowers. This washer prevents gasoline leaks from the carburetor by sealing the bolt to the bowl.The washer seal is normally replaced when overhauling the carburetor. Reusing the old one is not recommended. If the seal between the bolt and the bowl is not tight, gasoline could leak and cause damage to the engine or cause bodily injury due to combustion. There are normally two bolts on the carburetor bowl. Each bolt will have a washer seal. It is a good idea to replace both seals at the same time to ensure both are flush with the bowl.When replacing the washer seal, it has to be flush and tight but not overtightened. If it is overtightened, it can crack and strip, making it leak and useless. If necessary, the washer can be trimmed to make a tighter fit. After making sure the fit is flush, it slides over the bolts that make the connection from the bolt to the bowl. The bolts are then tightened.This OEM Midwest Engine washer seal is sold individually for Briggs and Stratton lawn mower and lawn tractor engines.

This is a genuine float needle valve that is designed to be used in select small engines found in lawn tractors. The float needle is located in the carburetor and is responsible for assisting with the intake and outflow of gas through the assembly. As the fuel bowl in the carburetor fills and drains, this needle regulates how much fuel is present to ensure the proper operation of the engine. Over time, the valve can become cracked or get damaged because of repetitive motion and exposure to high heat. This could impact the flow of fuel and the engine performance, or cause the engine to fail completely. This genuine OEM float needle valve is manufactured to exact standards as an identical replacement for select Briggs & Stratton small engines found in lawn tractors. It can also be used with certain models from Toro and Vanguard. It is sold as an individual unit and made of durable plastic. Be sure to drain the fuel from the engine and allow it to cool before doing any repairs. Gloves are also recommended for safety. For those who need additional components, this valve may also be available as part of a compatible carburetor rebuild kit.

The fuel cut-off valve is used as an external mechanism to stop the flow of gasoline from the fuel assembly to the engine to conserve fuel and maintain safe operation. If your device did not come with a cut-off valve, this is an easy install to give more control over the engine’s operation. When installing a fuel cut-off valve in your small gasoline engine, the first thing to note is the little arrow on the side of the valve. This indicates the direction that fuel will be flowing from the tank to the motor. Empty the fuel tank before proceeding with the repair. Remove the fuel line from the tank and cut the hose in two. Install properly sized hose clamps on either side of the cut and force the two ends of the valve into the severed line. Reattach the fuel lines and fill the tank. This fuel cut-off valve is compatible with a variety of gasoline-driven tools, including lawnmowers, generators, snowblowers, and chippers. Brands that use this OEM replacement part include Craftsman, Briggs & Stratton, Snapper, Simplicity, Toro, and Cub Cadet. This OEM part is sold individually.

This is a genuine replacement for the camshaft in select Briggs & Stratton engines. The camshaft is found in the crankcase assembly and is designed to help turn the crankshaft to power the engine. This part helps crank the engine and so it is exposed to constant wear and repetitive motion, which can cause it to deteriorate with regular use. It can also break or become damaged due to impact. Without a properly functioning camshaft, the engine will not be able to function, so a failed part must be replaced. This genuine OEM camshaft is manufactured to specific standards and designed to fit select Briggs & Stratton and Toro equipment that has compatible engines. This camshaft includes the part itself along with two metal tappet valves, and is sold as an individual unit. This part is made of durable metal. Other components are sold separately. Allow the engine to cool completely before performing any repairs and always wear gloves to provide hand protection when working on lawn and garden equipment and engines.

This is a genuine replacement fuel tank cap for select Briggs & Stratton engines. It seals the fuel tank to keep the fuel contained and also to create the pressure required to run the fuel system and lead to the combustion process. The fuel cap screws onto the fuel tank and can become worn over time. The cap can also become damaged due to an impact or another incident. In some cases, the cap can get lost or the threads can break or strip entirely. A replacement cap like this one can be the solution for compatible models. This OEM fuel tank cap is manufactured to specific standards by Briggs & Stratton and will fit select models of vertical and industrial engines, including 3.5, 5, 7, 9, and 12.5 HP models. It can also be used on select Toro, Murray, Simplicity, and Snapper models that have a Biggs & Stratton engine and/or fuel tank. The non-vented cap ensures appropriate sealing and fuel containment, and it is made of durable composite plastic material. This fuel tank cap is sold individually. No tools are required to replace this part.

The oil seal plays an important role in protecting the oil as it flows into the crankshaft and engine block. It creates a strong seal and ensures that the oil can flow effectively into the engine for proper operation. Over time, rubber seals degrade and wear out, so their replacement will be a part of routine maintenance. If there are oil leaks around the crankshaft or engine, this seal may be the culprit. Replacing the oil seal will ensure proper oil pressure and avoid oil leaks that could lead to more serious damage. When installing this replacement part, it is important to use a rubber mallet or large socket to tap the part into place. This is a genuine Briggs & Stratton part that is a replacement for various compatible small engines. It can fit select engines on Toro, Husqvarna, and Briggs & Stratton equipment. This oil seal is sold individually and compatible with a variety of engines. This OEM replacement is made of durable rubber and sold individually.

This carburetor overhaul kit is made for use with various lawn and garden machines with small engines. It offers a selection of parts that are needed to get a lawnmower running again if issues are happening with the carburetor. The carburetor is a component that is inside the tool. It controls the mixture of air and fuel that reaches the cylinder to ignite and ensure the engine starts running.If a lawnmower or snowblower doesn't start even when the fuel tank is full, this is an indication that the carburetor may no longer be functioning properly. There is an easy method to test whether this is the case. Take out the air filter and then place a small amount of fuel into the carburetor. Pull on the starter rope and watch to see if it starts up. It should start and run for a moment but then die again. If this is the case, the carburetor likely has an issue and needs to be rebuilt or replaced.Designed for use in lawnmowers and snowblowers, this carburetor overhaul kit fits tools by Briggs & Stratton, Simplicity, Toro, MTD, and Cub Cadet. This is an individual kit that is genuine OEM and directly sourced by the manufacturer.

Magneto Armature, also known as an Ignition Coil

This fuel pump is a genuine Midwest Engine part, sold individually. This fuel pump can be used as a replacement part or a lawn tractor. The purpose of a fuel pump is to provide a passageway for fuel to channel through the fuel line and into the fuel tank.The fuel pump of a lawn mower or a lawn tractor might eventually have to be replaced in the event that it suffers damage and cannot perform its crucial function. If the fuel pump has been torn, scraped, punctured, or eroded from general wear and tear with long-term use or as the result of a direct impact with a hard object such as a rock or a curb, the component should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This fuel pump is compatible with the following outdoor appliance brands: Midwest Engine, Briggs & Stratton, Cub Cadet, Simplicity, and Toro.

Small motors require electrical supplies, and the voltage regulator in any engine maintains the voltage from the power source at an acceptable level. It will keep voltage in a specific range that the device can tolerate. This voltage regulator is designed for use in small engines made by or used in motors for Briggs & Stratton, Toro, and Vanguard machines. It is meant for 10-16 amp voltage regulation and includes all of the wiring needed to do the job. It works well with an array of garden machine and lawn machine engines, and will regulate the electrical systems. This is an OEM replacement part that requires a screwdriver and socket set to both remove and then replace. The voltage regular ships individually.

This grip-starter rope is a genuine Midwest Engine replacement part for outdoor appliances with small pull start engines, such as lawn mowers, snowblowers, wood-chippers, leaf blowers, and chainsaws. The grip-starter rope is the piece that allows an appliance user to start the engine by pulling the rope; this mechanism can be referred to as a recoil starter, a starter rewind, or a rope start as well. Any damage to a grip-starter rope will be obvious to the naked eye; while the problems with the actual starting mechanism of a pull start-operated engine might be more difficult to assess and root out, the damage to the actual grip-starter rope itself will come in the form of tears, rips, and general time-worn erosion of the casing material of the rope. If there is significant tearing on the rope itself, this replacement grip-starter rope can serve as a replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This grip-starter rope is compatible with the following brands: Briggs and Stratton, Toro, Cub Cadet, and Simplicity.

A hose clamp serves the basic purpose of holding together two connecting hoses. This is a crucial job in an engine. Since there are so many connecting tubes and hoses transferring oil and fuel within an engine, a leak could prove catastrophic. It could not only cause the engine to malfunction but could also become a fire hazard. Replacing a hose clamp is an easy job, though the exact process will depend on where the connection is located. A pair of pliers may be needed. This is a genuine OEM replacement part and will work with a wide range of appliances, such as pressure washers, engines, generators, tractors, mowers, blowers, shredders, and chippers from Murray, Toro, Briggs & Stratton, Snapper, MTD, Lawn-Boy, or Simplicity. This part ships individually.

Almost all small gasoline engines are started by pulling a starter rope, which initiates the compression in the cylinder that fires a spark plug, igniting the air-fuel mixture that starts a small gasoline engine. Starter ropes may become frayed with use and have to be replaced. Replacing the starter rope is not time-consuming. Begin by removing the shroud, the part of the manifold that covers the starter pulley. After removing the old starter rope, insert one end of the new rope into the pulley assembly and tie a knot in it so it won’t slip out of the slot. Then feed the rope into the starter pulley assembly by holding tension on the rope and using a screwdriver to turn the pulley assembly counter-clockwise until it is taut. Hold the pulley in place with the screwdriver to keep the spring from unwinding as you replace the shroud over the assembly. Keeping the tension on the rope, remove the screwdriver. The only thing left is to attach the starter rope to the mower handle. This starter rope is a genuine OEM manufacturer’s replacement part made by Midwest Engine. It is designed to work on most any Briggs & Stratton, Simplicity, Cub Cadet, or Toro made small engine. These engines are used on lawnmowers, chippers, and other small engines. It is sold individually.