267Abrs Parts

Main wire harness for washer dryer combos. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connections are loose.

This replacement drum assembly is the rotating cylinder that tumbles laundry in your dryer. Replacing a damaged or out-of-round drum restores smooth, quiet tumbling and helps protect fabrics from snags, scraping, and uneven drying.

• Forms the rotating chamber that holds clothes; driven by the belt and motor to tumble items for drying
• Works with drum seals and lifters/baffles to maintain airflow and separate fabrics for even drying
• Replacing a dented, cracked, or out-of-round drum can resolve thumping, scraping, or rumbling noises
• Addresses sharp seams, loose spots, or rust that can snag/tear clothing or leave marks

• Disconnect power; shut off gas supply for gas models before service
• Remove top/front panels and release belt tension to lift out the old drum; note belt routing
• Compare parts and move over any reusable, model-specific components if required
• Inspect belt, idler pulley, bearings, and felt seals while open; replace if worn

Seals dryer exhaust duct connection to contain airflow and prevent lint entering cabinet. Replace if cracked or loose to restore efficiency. Verify fit.

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

Secures wiring and hoses in your laundry center to prevent rubbing and wear. Replace when broken or missing to maintain proper routing. Verify fit.

Replaces damaged or worn control panel face on laundry centers. Restores front appearance and provides secure mounting for controls. Needed when cracked or broken.

Retaining clamp secures hoses and tubes to prevent leaks and loose connections in your washer dryer combo. Replace if worn or damaged. Verify fit with model.

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two

Secures front panel on laundry centers. Replace if broken or panel becomes loose. Verify fit with your model number before ordering this clip.

Secures and routes the drain hose in your washer dryer combo. Replace if the original stop is cracked, broken, or missing to properly support the hose.

Left-side hinge cover for laundry center washer lids. Restores appearance and protects hinge assembly. Replace if cracked, broken, or missing.

Replacement hex washer head screw for laundry center panels and components. Needed when original fasteners are stripped, missing, or damaged during repair.

Replacement door hinge bushing for laundry centers. Restores smooth pivot operation when original is worn, cracked, or causes door misalignment or sticking.

Fix rattling panels or loose trim with this push-on speed nut. Secures components to studs and shafts for a tight fit. Quick 5-minute installation.

Fix loud grinding noises or motor wobble with this dryer motor mounting plate. Secures the motor assembly to prevent vibration and damage.

Exhaust duct channels air from your laundry center to the venting system. Replace if cracked, disconnected, or damaged to restore proper airflow.