267Abrs Parts

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly

A small replacement hose clip that secures flexible appliance hoses to fittings to help prevent leaks and disconnections. Fits commonly used appliance hose connections to restore a secure seal and reliable water flow. What it does:

• Secures a water or drain hose to a barb or fitting to prevent the hose from coming loose
• Helps stop leaks and drips caused by loose or slipping hoses
• Prevents hose movement and rubbing that can lead to wear or abrasion
• Useful when a hose slips off during operation or after maintenance

• Disconnect power and shut off the water supply before servicing the appliance
• Use appropriate hand tools (needle-nose pliers or hose clamp pliers) to open and seat the clip
• Position the clip over the fitting and tighten until the hose is snug and secure; avoid over-tightening
• Replace only with the correct OEM-style clip for a proper fit

This factory service kit is engineered for the 27-inch Centauro front-load washer platform. It refreshes critical tub and basket components to help restore smooth, quiet spinning and consistent wash performance.

• Maintains proper drum rotation, alignment, and sealing within the tub/basket system
• Helps address rumbling or grinding during spin, excessive vibration/wobble, or water near the tub area
• Restores a secure fit between rotating and stationary tub components
• Platform-specific fit for correct clearances and balanced operation

• Disconnect power and water before servicing; wear gloves and eye protection
• Access typically requires removing top/front panels and door boot; support the tub and drum during disassembly
• Transfer and torque fasteners evenly per service instructions; re-level the washer after reassembly
• Run a test rinse/spin and check for noise and leaks before returning to service

This exhaust blower gasket seals the joint between the dryer's blower outlet and exhaust duct. It helps maintain proper airflow and contain lint and heat, supporting efficient drying and preventing leaks into the cabinet or laundry area. What it does:

• Seals the blower-to-exhaust connection to prevent air and lint leaks
• Helps maintain designed airflow through the drum and vent system
• Can reduce warm air or lint escaping inside the cabinet

• 1 gasket

• Disconnect power; for gas dryers, shut off gas and disconnect the supply. Allow the dryer to cool.
• Access the blower housing/exhaust duct; remove panels as needed.
• Remove the old gasket and any residue; clean mating surfaces and lint before installing.
• Seat the new gasket evenly and reassemble; avoid overtightening fasteners and ensure the home vent is clear.

The agitator screw secures the washer's agitator to the drive shaft so it can move clothes effectively during the wash cycle. Replace a lost, stripped, or rusted screw to help stop wobble and restore proper agitation.

• Fastens the agitator to the drive shaft/coupler to transfer motion
• Address a loose or wobbly agitator, rattling/clunking, or weak/intermittent agitation
• Replace if the original screw is missing, corroded, or has stripped threads or head
• Helps prevent the agitator from lifting off during operation

• Disconnect power and ensure the washer is empty before servicing
• Remove the fabric softener dispenser and agitator cap to access the fastener
• Align parts, start the screw by hand to avoid cross-threading, then tighten snugly—do not overtighten
• Reinstall caps/dispenser and run a brief test cycle to proper agitation

This suspension rod support socket replaces the plastic cup the suspension rod sits in on a top-load washer. Replacing a worn socket restores smoother tub movement and helps reduce vibration and noise during wash and spin cycles.

• Supports the suspension rod at the tub/frame connection point
• Provides a low-friction pivot to stabilize the basket
• Helps reduce excessive shaking and out-of-balance banging
• Common signs of failure: cracks, squeaks/scraping, or the rod popping out

• Unplug the washer and shut off water supply before servicing
• Access the suspension area per your model (remove top/front panel as needed)
• Support the tub, relieve tension on the suspension rod, swap the socket, and ensure the rod seats fully in the new socket
• Reassemble, level the washer, and run a test spin to check balance

This 27" basket assembly replaces a damaged or worn dishwasher rack so you can securely load dishes and slide the rack smoothly. It restores stable support for plates, bowls and glassware and improves rack alignment. What it does:

• Provides the main lower/upper dish support surface so items sit securely during wash cycles
• Restores smooth in-and-out rack travel when original basket is bent or worn
• Prevents dishes from shifting or contacting each other due to damaged tines or walls
• Helps reduce clattering, scraping or poor wash coverage caused by a misshapen rack

• One 27" basket assembly as shown

• Disconnect power to the appliance and shut off the water supply before beginning any work
• Remove remaining dishes and carefully lift out the old basket; handle edges and glassware with care
• Align the basket on the rack rails and slide into position; verify rollers/wheels engage the track
• If the basket is large or awkward, have a second person assist to avoid dropping or damaging the part

This motor strap secures the appliance motor to the cabinet, keeping the motor stable during operation to reduce vibration and noise. Use this replacement to restore proper motor positioning and support in compatible models. What it does:

• Holds the motor firmly in place to prevent movement or shifting during use
• Helps reduce vibration and associated noise caused by a loose motor
• Maintains correct motor alignment so belts and linkages run smoothly
• Commonly used when a worn or broken strap allows motor sag or misalignment

• One motor mounting/retaining strap

• Disconnect power to the appliance before beginning any work
• Inspect mounting points and fasteners; replace any damaged hardware as needed
• Secure strap to the motor and cabinet using the original mounting holes and recommended hardware

This is a genuine GE replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. A simple fastener that helps keep assemblies aligned and functioning safely. What it does:

• Secures panels, brackets, and small components in place
• Prevents noise from loose parts and maintains structural alignment
• Restores proper fastening after repairs or wear
• Matches OEM fit for reliable replacement

• Disconnect power to the appliance before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully and tighten until snug; do not overtighten to prevent damage
• Replace any damaged or missing fasteners with the same OEM part for best results

A replacement pin alignment used to correctly position and secure moving parts in appliance hinge or latch assemblies. Restores proper alignment to reduce sagging, rubbing, or uneven operation for smoother, quieter performance. What it does:

• Aligns and secures hinge or latch components to maintain correct movement and fit
• Helps stop door sag, binding, or uneven closing when the alignment pin is worn or damaged
• Reduces rubbing and noise caused by misaligned parts
• Restores proper clearance for seals and moving assemblies

• One pin alignment

• Refer to the appliance OEM service manual for model-specific removal and installation steps
• Disconnect power (or unplug) and, if applicable, remove stored contents before working on doors or hinges
• Use basic hand tools; avoid forcing parts or over-tightening fasteners to prevent damage
• If alignment issues persist after replacement, inspect associated hinges, brackets, and fasteners for wear

This replacement drum assembly is the rotating cylinder that tumbles laundry in your dryer. Replacing a damaged or out-of-round drum restores smooth, quiet tumbling and helps protect fabrics from snags, scraping, and uneven drying.

• Forms the rotating chamber that holds clothes; driven by the belt and motor to tumble items for drying
• Works with drum seals and lifters/baffles to maintain airflow and separate fabrics for even drying
• Replacing a dented, cracked, or out-of-round drum can resolve thumping, scraping, or rumbling noises
• Addresses sharp seams, loose spots, or rust that can snag/tear clothing or leave marks

• Disconnect power; shut off gas supply for gas models before service
• Remove top/front panels and release belt tension to lift out the old drum; note belt routing
• Compare parts and move over any reusable, model-specific components if required
• Inspect belt, idler pulley, bearings, and felt seals while open; replace if worn