302Ts Parts

The Pressure Regulator is an OEM part for Frigidaire gas ranges. It controls incoming gas flow to the burner valves and maintains consistent heat levels.

Causes of a bad pressure regulator can include cracks or leaks developing in the seal over time, clogs or debris buildup affecting flow control, or damage to pressure monitoring components.

Symptoms of a bad pressure regulator include:

• Fluctuating burner flames and heat output
• Inability to stabilize gas pressure for predictable cooking
• Yellow or sooty flames indicating inefficient combustion
• Safety risk of gas leaks at increased pressures

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This ferrule is a small compression fitting used to secure and seal a refrigerator water line connection, helping stop leaks and maintain proper flow to the ice maker or dispenser. It's a simple replacement to restore a tight water connection. What it does:

• Secures tubing to a compression or shutoff fitting to prevent leaks at the connection
• Restores a proper seal for water supply lines feeding the ice maker or dispenser
• Commonly used when a loose, dripping, or leaking water line is present
• Helps prevent water damage from failing or corroded fittings

• One ferrule

• Turn off the water supply and relieve line pressure before servicing
• Confirm tubing is cut square, fully inserted, and the ferrule is seated before tightening
• Tighten fittings per manufacturer guidance; avoid over-tightening which can damage tubing
• After installation, turn water back on and check carefully for leaks

This elbow is a threaded pipe fitting that redirects and secures a fluid line connection where space or alignment requires a 90° turn. It provides a compact, threaded junction to connect compatible appliance tubing or hose to a valve or port. What it does:

• Connects two threaded line ends at a 90° angle for tight routing in confined spaces
• Provides a sealed, threaded junction between a 1/2 in. NPT inlet and a 9/16-24 threaded outlet
• Helps stop leaks and maintains proper line alignment when the original elbow is worn or damaged
• Commonly used where a bent or cramped connection prevents a straight coupling

• One elbow fitting (1/2 in. NPT x 9/16-24)

• Turn off and depressurize the water supply (or system) before removing or installing fittings
• Start threads by hand to avoid cross-threading; tighten with appropriate wrench until snug
• Use plumber's tape or thread sealant only if specified by the appliance manufacturer

This backguard glass is the upper backsplash panel that restores the appearance and protective surface behind your range's controls. Replaces cracked, chipped or discolored glass to help keep the control area looking clean and finished. What it does

• Covers and protects the range backguard area and control mounting surface.
• Replaces cracked, shattered or heavily scratched glass that can expose internal components.
• Restores a uniform finished look when the original glass is stained, discolored, or broken.
• Helps prevent grease and spills from contacting inner components behind the control area.

• One backguard glass panel.

• Disconnect power to the appliance and ensure the range is cool before starting.
• Handle glass carefully; wear cut-resistant gloves and eye protection to avoid injury.
• Require removing control panel/trim and fastening hardware—keep mounting screws and brackets for reassembly.
• If glass is shattered, remove all fragments and clean mounting surfaces before installing replacement.

This replacement wire clip secures refrigerator wiring to the cabinet side to keep harnesses organized and protected from abrasion. It helps prevent loose or pinched wires that can cause noise or intermittent electrical issues. What it does:

• Holds wiring harnesses against the refrigerator bodyside to prevent movement and wear
• Reduces rattling or vibration caused by loose wires
• Helps prevent chafing or pinching that can lead to intermittent connections or shorts
• Keeps wires routed away from moving parts and sharp edges

• One wire clip

• Disconnect power to the appliance before servicing to avoid shock
• Access may require removing an interior panel or trim; keep fasteners organized
• Clip typically snaps into a matching slot or fastener point; align wiring and press clip into place