30430B Parts

This burner mounting screw fastens the surface burner assembly to its base on the cooktop, keeping it stable and properly aligned. Replace stripped, rusted, or missing screws to eliminate wobble and maintain even flame positioning.

• Secures the surface burner to the orifice holder/cooktop assembly
• Helps keep the burner level, stable, and properly seated
• Can address a loose or wobbly burner or one that lifts when removing the grate/cap
• Restores proper seating when original hardware is lost or corroded

• Disconnect power and shut off the gas supply; allow the cooktop to cool completely
• Remove grate, cap, and burner head (as designed) to access the fastener
• Start threads by hand and use the correct driver to avoid cross-threading
• Tighten snugly without overtightening; clean or chase threads if corrosion is present

Replacement oven door seal that creates a heat-tight barrier around the oven door to help maintain oven temperature and reduce heat loss. Restores proper door sealing for more even cooking and safer operation. What it does:

• Seals the oven cavity to retain heat and stabilize cooking temperature.
• Helps prevent heat, smoke and odors from escaping the oven during use.
• Replace when the gasket is cracked, flattened, torn, brittle or the oven takes noticeably longer to preheat.
• Improves door closure and can reduce energy loss when installed correctly.

• Disconnect power (and gas if applicable) and allow the oven to fully cool before starting.
• Remove the old gasket per the oven's service instructions; some models require removing the door or loosening fasteners.
• Press the new gasket into the door channel evenly, working around the perimeter so the seal seats flush.
• Wear gloves to protect hands from sharp edges.

This burner cap sits on top of a gas cooktop surface burner to shape and protect the flame for even heating and safe operation. It restores proper flame pattern and helps keep the burner head clean. What it does:

• Covers the burner head to direct gas flow and create an even flame
• Helps prevent food and spills from clogging the burner ports
• Can improve ignition consistency and reduce yellow or uneven flames
• Replaces cracked, warped, or missing caps that cause poor heat distribution

• One replacement burner cap

• Ensure the appliance is OFF and completely cool before servicing
• Lift off the old cap and set the new cap in the correct position on the burner head
• No special tools required; verify the cap sits flat and centered before use
• Inspect for cracks or heavy corrosion; replace if damaged

Replacement switch burner igniter that produces the spark needed to light a gas burner, restoring reliable ignition so burners light quickly and consistently for safer cooking. What it does:

• Generates the ignition spark to light a gas cooktop or range burner.
• Restores normal ignition when a burner won't spark or lights inconsistently.
• Stops intermittent clicking or repeated attempts to light caused by a failed igniter.
• Works as the electrical spark source paired with the burner valve and cap.

• Disconnect electrical power and shut off the gas supply before servicing.
• Access typically requires removing the cooktop or control panel—handle panels and wiring gently.
• Reconnect wires to matching terminals; do not force connectors or bend contacts.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

This body-side spacer installs on the cabinet side of the door or lid hardware. It sets the correct stand-off and alignment so the handle or latch feels solid and sits flush for a clean, secure fit. What it does:

• Positions and supports door/lid hardware on the cabinet/body side
• Maintains proper spacing to help prevent rubbing or scuffing of the panel
• Helps keep the handle or latch tight and aligned
• Common symptoms: loose or wobbly handle/latch, uneven alignment, visible gap or scuff marks at the mounting point

• Includes 1 body-side spacer

• Disconnect power to the appliance before servicing
• Support the handle/latch, remove the cabinet-side mounting screws, place the spacer, realign hardware, and reinstall screws snugly
• Reuse the original fasteners; avoid overtightening to prevent cracking the spacer or stripping threads
• Check door operation and alignment before finishing

A single gas burner orifice that meters fuel flow to a range or oven burner for consistent flame sizing and reliable cooking performance. Replaces a worn or clogged orifice to help restore steady ignition and even heat. What it does:

• Controls the amount of gas delivered to a burner for proper flame height and heat output
• Helps maintain consistent cooking and baking temperatures when functioning correctly
• A clogged or damaged orifice can cause weak or uneven flames, slow ignition, or poor heating
• Works as a small, precision-fit insert that sits in the burner assembly

• Turn off the appliance and shut off the gas supply before servicing
• Use a wrench or socket sized to the orifice and avoid rounding the fitting
• Inspect burner ports and clean any debris before installing the new orifice

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

Specs: 8 - 18 x 0.500

The Lens is an OEM component for Frigidaire freezers. It acts as a transparent cover and protective barrier for the freezer compartment lights. Crafted for durability and clarity, the lens avoids frost and minimizes condensation while allowing visibility inside the freezer.

Causes of a bad lens can include deep scratches or cracks developing over time from repeated wiping or exposure to chemicals like frost removers.

Symptoms of a bad freezer lens include:

• Cloudiness, fogginess, or smears inhibiting internal visibility
• Cracks or breaks compromising the protective barrier
• Distorted views make it difficult to assess food levels
• Diffused lighting with shadows instead of a clear view

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Note: ONE screw only, order as needed.