504Pnrt3u166 Parts

Replacement mounting screw for gas cooktops. Secures panels, trim, and brackets. Needed when original screw is stripped, missing, or damaged during repair.

Hex screw for lawn mowers, tractors, and snow blowers. Replaces worn, corroded, or missing screws on engines and housings. Identical fit for secure assembly.

This high voltage capacitor works with the diode and magnetron to generate the microwave energy needed to heat food. It stores and releases electrical energy to nearly double the voltage output from the transformer. Replace this capacitor if the microwave runs but does not heat, makes a loud buzzing noise, or if the unit trips a breaker - always discharge the capacitor before handling as it can retain a dangerous charge even when unplugged.

This is a ceramic glow-bar igniter for gas ovens. It heats to ignite the gas for baking or broiling, restoring reliable oven lighting and even heating without repeated clicking or open flames.

• Heats up to light the gas burner in the oven cavity
• Common fix for oven not heating, long preheat times, or burner that lights then goes out
• Designed for ovens that use a glow-bar (hot surface) ignition system

• Disconnect power and shut off gas before servicing
• Handle the ceramic element carefully; avoid touching the carbide tip
• Test for proper ignition and observe a full heat cycle after installation

The Lamp is an original and genuine OEM replacement part for Frigidaire microwaves. It is located inside the microwave and provides light to easily see food and monitor cooking progress.

Causes of a bad lamp can be natural bulb burnout over time, damage from foods accidentally jostling the lamp during cooking, or general wear and tear.

Symptoms of a bad lamp include:

• Dimming or flickering light inside the microwave when in use
• No light turning on when the microwave is powered on
• Broken or cracked bulb housing

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a mesh grease filter that fits inside a range vent hood to capture grease and airborne particles produced during cooking. It helps keep the exhaust system clean and prevents grease buildup in the ductwork. Replace this filter if it appears heavily discolored, clogged with grease, or no longer effectively traps cooking vapors.

Bell washer adds spacing on shafts in lawn tractors, tillers, mowers, and chipper shredders. Replace if washer is missing, worn, or damaged during maintenance.

The Thermostat is an OEM part for Frigidaire microwaves. The thermostat accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

This thermostat monitors the internal temperature of the microwave and helps regulate heating to prevent the appliance from overheating. It acts as a safety device that cuts power to certain components if temperatures exceed safe limits. Replace this thermostat if the microwave shuts off unexpectedly during use, fails to heat properly, or if diagnostic testing shows the thermostat is no longer opening or closing at the correct temperature.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

This electromechanical switch assembly controls a specific user or internal function and restores reliable on/off or selection response. Replace a worn or damaged switch assembly to regain proper control and appliance usability. What it does:

• Acts as the electrical switching component for the appliance control circuit
• Enables user input to be registered (on/off or selection) and sent to the control system
• Common symptom: appliance won't respond when a control is pressed or switched
• Common symptom: intermittent or non-working control operation, no clicking or circuit continuity when activated

• Disconnect power before accessing or replacing the switch to avoid shock
• Access panel or control bezel removal may be required
• Handle wiring connections carefully; match terminals and secure connectors

Fix a microwave that won't start, has no display, or ignores settings with this electronic control board. Restores all functions and user controls.

This is a cooling fan motor used in a microwave oven to circulate air and prevent internal components such as the magnetron and electronics from overheating. It typically runs during cooking and may continue running briefly after the microwave shuts off. Replace this motor if the microwave is overheating, shutting off unexpectedly, or if the fan is noisy, runs sluggishly, or doesn't spin at all.

Secures internal components to the microwave chassis. Replace if cracked, broken, or missing to restore proper support and stop rattling or misalignment.

Microwave not heating or making buzzing noises? This diode rectifier allows current flow in one direction and protects circuits. DIY repair takes 30 minutes.

This mechanical thermostat controls refrigerator temperature by sensing evaporator or cabinet temperature and switching the compressor and fans on and off. Replaces a worn or faulty control to help restore consistent cooling and temperature regulation. What it does

• Senses temperature and closes/open circuit to run the compressor and cooling fans
• Helps maintain set temperature by cycling refrigeration system components
• Commonly linked to symptoms like warm or fluctuating temperatures, compressor not running, or continuous running
• Works as the control point for user temperature settings

• One thermostat

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Access may require removing interior panels or control housing
• Handle sensing bulb and capillary tube carefully to avoid kinks or damage