6002L Parts

This retaining ring secures a shaft or component in-place to prevent axial movement and wear, restoring proper alignment and reducing noise or wobble. It's a small, durable replacement part for assemblies that use a snap-style ring. What it does:

• Holds shafts, bearings or components axially in their mating grooves to prevent shifting.
• Stops rattling, grinding, or excessive play caused by a worn or missing ring.
• Keeps assemblies aligned to reduce premature wear on surrounding parts.
• Provides a simple replacement solution when the original ring is bent, broken, or lost.

• Disconnect power and/or water and remove any panels needed before starting work.
• Use snap-ring pliers or the manufacturer-recommended tool to safely remove and install the ring.
• Inspect grooves and mating surfaces for damage or debris and clean before installing the new ring.
• Wear eye protection and keep fingers clear—snap rings can spring out during removal or installation.

This strike screw secures the door strike/catch to the appliance, keeping the latch aligned so the door closes firmly and any safety interlock engages. Replacing a missing, stripped, or corroded screw helps restore reliable, consistent door latching. What it does:

• Fastens the strike/catch to the door or cabinet
• Maintains proper alignment for positive latch engagement
• Helps address issues like door not latching, loose/rattling door, or intermittent door switch activation
• Replace if threads are stripped, the head is damaged, or the screw is missing

• 1 strike screw

• Disconnect power before servicing; allow hot surfaces to cool. For gas appliances, also shut off the gas supply.
• Support the door or strike and remove the damaged/missing fastener.
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening.
• Verify door alignment and latch/lock operation after installation.

Tub to pressure switch hose.

This replacement door gasket seals the refrigerator/freezer door to help maintain consistent temperatures and reduce frost buildup. It restores the cabinet seal so the appliance can cool efficiently and run less often. What it does:

• Provides an airtight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and freezer run time caused by leaks
• Can stop common symptoms like warm spots inside the compartment, excessive frost, or frequent compressor cycling
• Fits into the door channel and compresses to form a continuous seal when the door is closed

• Disconnect power to the appliance before starting any repairs
• Remove the old gasket and thoroughly clean the door channel before installing the new gasket
• Press the gasket evenly into the channel, working around the door to ensure a continuous, wrinkle-free seal
• Avoid using sharp tools that could damage the new gasket; allow the gasket to fully seat before checking for leaks

A hex screw fastens and holds two components together. It has a hexagonal head and features threading starting underneath the shoulder down to the tip. Its all-metal construction offers rigidity and longer lifespan. It is also threaded, so you can conveniently loosen or tighten in position. It measures 1/4-20 x 0.5 inch and comes in brass or gold color. Take note that this replacement hex screw may beused in different locations of a machine. Double check the device’s model number for compatibility. To install this hex screw, you will need a hex wrench or a hex socket. This hex screw is a replacement made by MTD. This screw/bolt may be used on lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, chainsaws, pole pruners, log splitters, or wood chippers made by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, or MasterCut. This OEM hex screw is sold individually.

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

This screw is a direct-replacement fastener used to secure appliance panels and components. It provides a simple, reliable fix when a missing or damaged screw lets parts sit loose or vibrate. What it does:

• Secures service panels, trim pieces, brackets, or small components
• Restores proper fit and alignment to reduce rattling or movement
• Replaces stripped, missing, or corroded screws to maintain safe assembly
• Works wherever the OEM screw specification is required for reliable fastening

• Use the correct driver bit and turn gently to avoid stripping the head
• Ensure mating threads are clean and aligned before tightening
• Tighten until snug; do not over-torque to prevent damage to threads or parts
• Disconnect power before working near electrical components or controls

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This OEM replacement push cap can be used in a variety of lawn and garden equipment. The push cap is secured to the end of a shaft, providing protection to the user from the sharp metal edge of the shaft. The push caps that are included with the machines may wear out over time or fall off in some cases, creating an injury risk involving sharp metal edges. These push caps are high-quality and made from durable plastic. They are easy to install. The OEM push cap is a genuine part made by the original manufacturer, to ensure quality and s proper fit. The push caps can be used on lawn tractors, chippers, shredders, log splitters, and other equipment. Some of the brands that this push cap is compatible with include MTD, Husky, Yard-Man, Bolens, Troy-Bilt, Ryobi, Yard Machines, and cub Cadet.

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

Self leveling leg pad

One per package.

Carriage bolts are flat-tipped with round heads, and their function in small engine appliances is to fasten together components and to secure that connection with a nut. There are various reasons that a carriage bolt might have to be removed and replaced, among them misplacement of the small, easily lost part. Other reasons to replace a carriage bolt could include damage or erosion that prevents the bolt from attaching the materials to one another effectively. If a carriage bolt is subject to this kind of damage, it should be replaced before using the small engine appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This genuine MTD carriage bolt can be used as a replacement part for several different kinds of appliances that require small engines, including lawnmowers, snowblowers, wood-chippers, tillers, string trimmers, leaf blowers, and edgers. The OEM carriage bolt is compatible with the following brands: Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut. This part is sold individually.

Hex washer head ,10-32 x 0.375. Ground

This rubber lid grommet cushions and seals the lid edge to prevent metal-on-metal contact and reduce vibration and noise. It restores proper lid alignment and helps keep the top surface from chipping or scratching. What it does:

• Acts as a bumper between the lid and cabinet to reduce noise and impact
• Maintains correct lid spacing and alignment for smooth opening/closing
• Protects finish by preventing wear where the lid contacts the cabinet
• Reduces vibrations or rattling caused by a loose or worn grommet

• Accessible with basic tools; remove the lid or open to access mounting location as needed
• Clean mating surfaces before installing to ensure a secure fit
• Inspect adjacent hinges and fasteners while replacing the grommet
• Disconnect power if working near electrical components or moving parts