673000701089 Parts

Oven won't heat or ignite? This igniter kit solves slow heating and ignition failure in gas ovens. Moderate DIY repair in 30-60 minutes.

Replacement mounting screw for securing handles, panels, and internal components. Needed when original screws are stripped, lost, or broken during repairs.

Replacement broiler pan set for ovens. Includes pan and insert to catch drippings during broiling. Order if your original is missing, warped, or damaged.

Replace a broken or fatigued oven door spring to restore proper counterbalance. Installs behind side panel. Ensures door closes firmly and seals correctly.

This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.

• Fastens exterior panels, trim pieces, or internal brackets to the appliance chassis
• Replaces lost, damaged, or stripped hardware
• Helps prevent vibration, rattling, and gaps between parts
• Common signs you need this screw: missing hardware, loose or misaligned panel/trim, stripped head or threads

• Disconnect power before servicing; also shut off the gas supply
• Use the correct driver; start the screw by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping or cracking adjacent parts
• Repair or replace the mounting point before installing

Replace a cracked, stripped, loose, or missing surface burner control knob on your range. Attaches to the valve stem to restore secure grip and control.

Secures the thermostat or temperature sensor in position for accurate temperature control. Replace this clip if broken, cracked, or missing during cleaning.

Maintains correct gap between internal range components. Replace if worn, missing, cracked, or broken to restore proper alignment and prevent parts rubbing.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

Replacement 6-32 x 3/8" screw secures panels, brackets, and trim pieces on appliances. Restores proper fastening when original screws are lost or stripped.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or damaged.

Wire harness assembly for lawn tractors. Connects electrical components throughout the tractor. Replace if wires are frayed, damaged, or connectors are broken.

Throttle cable for lawn tractors. Connects the throttle control to the engine carburetor. Replace if cable is frayed, kinked, or broken.

Exhaust muffler for lawn mowers and tractors. Reduces engine noise during operation. Replace if cracked, rusted, or excessively loud from wear or damage.

This muffler is a genuine OEM replacement part sourced directly from the manufacturer for use on lawn and garden equipment. It reduces the noise coming from the exhaust. Being a metal part exposed to the elements, it is not uncommon for mufflers to corrode over time and need replacement. As a lawnmower part, the muffler may sustain damage from debris in the yard while mowing. In either case, the muffler should be removed and replaced to keep the noise level to a minimum.The engine and damaged muffler should be cool to the touch before repairing the lawnmower. Wear work gloves and safety goggles. Remove the spark plug from the lawnmower for extra safety. Locate the bolts securing the muffler to the lawnmower and loosen them to remove the muffler. Dispose of the old muffler and align the new muffler with the bolts. Attach the new muffler and tighten the nuts. Put the spark plug back in the lawnmower. This muffler is a high-quality metal part that is individually sold. It does not come with hardware. It is designed for use on lawn mowers and lawn tractors manufactured by MTD, Ryobi, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Poulan, and Husky.

Replacement foot pedal pad for lawn tractors and riding mowers. Installs on control pedals. Needed when original pad is worn, cracked, or missing.