71001872 Clock Parts

End cap for freezer door basket. Secures and supports tilt basket assembly. Replace if broken, cracked, or missing. Right-hand side installation.

Refrigerator won't respond or shows error codes? This power control board regulates operations and coordinates key components. DIY-friendly repair in 10 minutes.

Plastic tube that routes water between internal refrigerator components. Replace if cracked, kinked, leaking, or brittle to restore water flow.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

The Cap Cover is an OEM part for LG refrigerators. This cover is designed to protect and secure various components within the refrigerator, such as the water filter or other internal mechanisms. Its role is to ensure that these components are shielded from debris, moisture, and potential damage, maintaining the overall efficiency and cleanliness of the appliance.

Causes of a bad cap cover can include wear and tear over time, cracks or breaks from accidental impacts, or warping due to exposure to temperature fluctuations. Misalignment or improper installation can also contribute to the cap cover becoming damaged or ineffective.

Symptoms of a bad cap cover include:

• Loose or missing cover
• Visible cracks or damage on the cover
• Debris or moisture accumulating in areas meant to be protected
• Misalignment or difficulty in securing the cover properly

This OEM LG part is also compatible with Sears/Kenmore.

This holder bracket secures internal refrigerator components in place. Replace if your original bracket is cracked, broken, or missing to restore stability.

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Right side upper hinge.

Magnetic seal that runs around refrigerator door edge to keep cold air in. Replace if torn, loose, or failing to seal properly. Verify fit with model.

Covers and protects the interior compartment fan while directing airflow. Replace if cracked, broken, or missing to restore safe air circulation.

This fan blade attaches to the condenser fan motor located near the bottom rear of the refrigerator. It draws air across the condenser coils to dissipate heat and keep the refrigeration system running efficiently. Replace this blade if it is cracked, warped, or broken, which can cause loud noises, poor cooling performance, or the compressor overheating and shutting off.

This joint assembly is the connector that joins two refrigerator water tubes to form a tight, leak-resistant seal. Replace it to stop leaks at a line coupling and restore reliable dispenser and icemaker water flow.

• Connects two plastic water lines within the refrigerator's water system
• Maintains a watertight seal to prevent drips and air intrusion
• Common fix for leaks at a coupling or tubing that won't stay seated
• Symptoms include slow/sputtering dispenser, small/no ice production, or visible seepage at the connector

• Unplug the refrigerator and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Depress the connector collar to release the tubing; cut damaged tube ends square and fully insert tubing until it bottoms out
• Restore water and power, then check all connections for leaks

This assembly includes the auger motor that rotates to push ice from the ice bucket through the dispenser chute. The motor drives the auger blade, breaking up clumped ice and moving it toward the dispenser opening when you press the ice lever or button. Replace this assembly if ice is not dispensing, you hear the motor humming but the auger isn't turning, or the ice maker is no longer producing or delivering ice.

The refrigerator auger motor assembly is the motorized unit inside the freezer's ice dispenser that turns a spiral auger to push stored ice toward the dispenser chute when you request ice. It controls the flow and delivery of ice cubes or crushed ice to your glass. Replace this assembly when the dispenser motor hums but no ice comes out, the auger doesn't turn, or ice delivery has stopped completely.

Seals the refrigerator door to keep cold air in and moisture out. Replace when worn or deformed to restore proper cooling and reduce frost buildup.