722T1bc Parts

These top mounting brackets secure the dishwasher to the underside of the countertop to prevent shifting or tipping during use. Replace bent or missing brackets to maintain a stable, safe installation.

• Anchors the dishwasher to the countertop when top mounting is required
• Helps prevent forward tipping when racks are extended
• Restores a secure, level fit within the cabinet opening
• Common symptoms: loose or rocking unit; broken, bent, or missing brackets

• Disconnect power and water supply before servicing
• Pull the dishwasher forward enough to access mounting locations
• Position brackets flush under the countertop and fasten with manufacturer-approved hardware
• Ensure the dishwasher is level and anchored evenly on both sides

The Rack is an OEM part for LG dishwashers. It provides an adjustable configuration of prongs and wires to effectively wash a variety of dirty dishes. As the main washing component inside the dishwasher, the rack is purposely designed to lift and tilt dishes to maximize water coverage.

Causes of a bad rack can include breaks, bends, or detachments resulting from overloading or improper loading of dishes. Mineral buildup may also occur over time.

Symptoms of a faulty rack include: 

• Inability to securely hold dishes in place during washing cycles
• Dishes not getting fully clean due to inadequate water distribution  
• Damage that causes rattling or noise during operation

This OEM LG part is also compatible with Kenmore dishwashers.

This hose connector joins an appliance hose to its mating port for a secure, leak-resistant connection. Replace a cracked or loose connector to stop drips at the joint and restore reliable flow through the line.

• Provides a secure coupling between a hose and an appliance fitting or another hose
• Helps maintain a tight seal to prevent leaks at the connection point
• Supports proper flow during fill, circulation, or drain operations
• Helps resolve issues such as dripping at the joint, a hose that won't stay attached, visible cracking, or intermittent fill/drain performance

• Disconnect power and, if applicable, shut off the water supply before servicing
• Place towels to catch residual liquid and relieve line pressure
• Transfer and tighten clamps or O-rings per your model; seat hoses fully on the connector
• Run a short test and inspect for leaks before returning the appliance to service

The Shaft,Nozzle is an OEM part for LG dishwashers. This part is located inside the dishwasher's spray arm assembly and is responsible for distributing water to the spray arms during the wash cycle.

Causes of failure can be mineral deposits that clog the nozzle openings or flexible shaft deterioration over time.

Symptoms of a bad shaft or nozzle include:

• Inadequate or uneven spray coverage inside the dishwasher
• Dirty dishes, especially on hard to reach areas
• Reduced water pressure during the wash cycle

This OEM LG part is also compatible with some Kenmore models.

This small sleeve bushing supports a pivoting or rotating joint in your dishwasher, providing a smooth bearing surface. Replacing a worn bushing helps restore quiet operation and protects mating parts from further wear. What it does

• Provides a low-friction surface between a shaft/pin and bracket
• Helps maintain proper alignment and reduces wobble at the joint
• Can quiet squeaks or grinding caused by wear
• Replacing a cracked or flattened bushing can improve smooth movement

• 1 bushing

• Disconnect power and shut off water before servicing
• Support the door or component attached to the joint to relieve tension
• Note orientation; transfer any spacers/washers in the same order
• Inspect the mating pin/shaft for wear and replace related parts if damaged

This dishrack tine replaces a damaged or missing row of prongs on your dishwasher rack, restoring secure spacing for plates, lids, and other items so they stay upright throughout the cycle.

• Attaches to the rack to provide prongs that hold dishes upright and separated for effective washing and drying
• Helps prevent items from tipping over or obstructing spray-arm movement
• Common signs it's needed: broken, bent, rusted, or missing tines; flaking coating; dishes not staying in place
• Restores rack organization and usable loading capacity

• Disconnect electrical power and turn off water supply before servicing
• Pull the rack out; release the retaining tabs/clips that hold the tine to the rack
• Remove the damaged tine, align the new tine with the mounting points, and secure it in place
• Ensure the rack slides freely and spray arms spin without interference before running a cycle

This pump casing assembly forms the sealed housing around the pump, channeling water through the system. Replacing a cracked or warped casing helps stop leaks and restore proper water flow and overall pump performance.

• Houses the pump impeller and seals the pump chamber to contain water
• Directs water flow between the tub/sump and the pump for efficient operation
• Helps maintain proper water pressure within the pump circuit
• Common symptoms of a failing casing include leaks near the pump area, weak water movement or poor draining, unusual grinding/rumbling noises, or visible cracks/warping

• Disconnect power and shut off water supply before servicing
• Access the pump (typically from the bottom or rear)
• Transfer any existing O-rings, clamps, and screws as needed; clean sealing surfaces
• Reassemble carefully, reconnect hoses, and run a test cycle to check for leaks

This gasket creates a watertight seal between mating parts in the dishwasher's water system. Replacing a worn or damaged seal helps stop leaks during cycles and maintains proper wash performance. What it does:

• Seals the joint between components such as the sump, pump housing, or inlet assemblies
• Prevents water leakage under pressure during fill, wash, and drain
• Helps maintain spray pressure by reducing internal bypass
• Common symptoms include water on the floor or in the base pan, and a flattened, cracked, or brittle old gasket

• One gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location and remove any retaining hardware
• Remove the old gasket and clean both sealing surfaces thoroughly
• Seat the new gasket evenly without twisting; tighten fasteners/clamps uniformly and run a test cycle to check for leaks

This door latch and lock assembly secures the dishwasher door and signals the control that it's safely closed. Replacing a worn latch restores firm door closure, a reliable seal, and consistent cycle operation. What it does:

• Locks the door so cycles can start and continue without interruption
• Helps compress the door gasket for a proper, leak-resistant seal
• Sends a door-closed signal to the control
• Common symptoms: won't start with the door shut, door won't latch or pops open, cycle pauses when jostled, water leaking at the door edge

• One door latch/lock assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the latch at the top of the door
• Note wire connector positions; move them to the new assembly and secure the latch
• Check latch engagement with the strike and adjust alignment if needed before reassembly

This guide assembly is the sliding rail that supports and aligns the freezer drawer. When worn or damaged, it can cause sticking, sagging, or poor sealing; replacing it restores smooth operation and proper drawer closure.

• Supports the freezer drawer and lets it glide smoothly in and out
• Keeps the drawer square and aligned with the front panel
• Helps the drawer close fully to maintain a proper seal
• Common symptoms: drawer hard to open/close, crooked or sagging drawer, grinding/squeaking, frost from incomplete closure, visible rail damage

• Disconnect power before servicing; empty the freezer drawer
• Pull the drawer out, remove the front panel and basket as needed
• Remove mounting screws and the old guide; reuse existing hardware if applicable
• Install the new guide, then verify both sides move evenly and the drawer seals properly

The WATER LEVEL SENSOR ASSEMBLY is an OEM component specifically designed for LG dishwashers. It is an electronic sensor responsible for monitoring and detecting the water level inside the dishwasher tub during each cycle. Precise water level detection allows the dishwasher to optimize water usage and ensure all cycles run as intended. 

Causes of a bad sensor assembly can include the buildup of sediment or minerals on the sensor contacts over time, leading to improper readings. Physical damage from impact could also affect sensor function.

Symptoms of a bad water level sensor assembly include:

• Incomplete or failed wash cycles 
• Error codes related to water issues
• Inability to fill or drain properly
• Flooding or leaks from the dishwasher 

Replace yours today with this genuine OEM LG part to maintain proper dishwasher operation. This OEM LG part is also compatible with Sears/Kenmore.

This component is a sump and motor assembly that is designed to be used on a dishwasher. This part moves the water from the sump collection area up into the spray arms.When the sump and motor assembly is faulty, the dishwasher may leak from the bottom. It is also possible that the dishwasher could run noisily. This high-quality OEM replacement part will fix these problems. If unsure if this part will fix the problems, consult a professional. Disconnect the appliance from the electrical outlet before performing care, maintenance, or replacing any parts on it. Some people performing this replacement may wish to wear work gloves to protect their hands during this process. The replacement process is very easy and takes about 15 to 30 minutes to complete from start to finish.This sump and motor assembly is compatible with dishwashers that are manufactured by LG. It is sold individually and sourced from the manufacturer.

The Micro Switch is an OEM part for LG dishwashers. It plays a crucial role in detecting when the door is securely closed prior to starting a cycle. This important safety feature prevents accidental exposure to hot water, detergent, and chemicals. 

Causes of a bad micro switch include degradation from years of repeated use, debris interfering with mechanisms, or damage from attempts to force or slam the dishwasher door closed.

Symptoms of a bad micro switch include:

• Cycles failing to start despite a closed door
• Hot water or steam visible escaping when running 
• The dishwasher not detecting the closed door position
• Error codes displayed related to door position sensors

This OEM LG part is also compatible with Sears/Kenmore. Replacing only when truly faulty helps ensure safe and reliable dishwasher function.
 

The Blower Motor Casing Assembly is an OEM part for LG dishwashers. This part houses the blower motor which generates airflow through the wash arms and drying vent. The casing is precision-engineered to fit securely within the dishwasher's structure.

Causes of a bad blower motor casing assembly can include cracked or warped plastic from repeated heating and cooling cycles. The seals around the motor connection points may also deteriorate over time.

Symptoms include:

• Incomplete or overly long drying cycle times
• Water pooling in the bottom of the dishwasher after cycles
• Sloshing or excess moisture noise heard coming from inside
• Irregular or strange smells emanating from within the unit

This LG part is also compatible with some Kenmore models.

This inlet hose supplies household water to the appliance's fill system. Replace a worn, kinked, or cracked hose to restore normal water flow and help prevent leaks that can lead to poor performance or damage. What it does:

• Connects the home water supply to the unit's inlet/fill connection
• Provides a sealed pathway for water during operation
• Helps maintain consistent water flow to the appliance
• Common symptoms: leaks at fittings, slow or no fill, visible kinks, bulges, or cracks

• Includes: One inlet hose

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve any line pressure
• Hand-thread fittings to avoid cross-threading, then tighten snugly—do not overtighten
• Restore water, check all connections for leaks, and test operation

By Frigidaire. 2+0 module type. Employs two spark electrodes for manual surface ignition of a four burner range top with flash tubes to front and rear burners. Very popular module used on many different brands and models. Check by appliance model number, if not sure.