79572051110 Parts

This LED light cover protects and diffuses the appliance's interior LED, restoring even lighting and a finished appearance. It is a direct-fit replacement designed to match the original factory lens. What it does:

• Protects the LED assembly from debris and impacts
• Diffuses and softens LED output for even interior illumination
• Restores a cracked, yellowed, or missing lens that affects light distribution
• Helps prevent direct contact with the LED board

• One LED light cover

• Disconnect power or unplug the appliance before starting
• Handle the lens carefully to avoid scratches; it typically snaps into place or is retained by a few clips
• Use a small screwdriver only if necessary to release retaining clips; avoid forcing parts

The Gasket Assembly Door is an OEM part for LG refrigerators. This gasket forms a seal around the refrigerator door, preventing warm air from entering and cool air from escaping, thus maintaining optimal temperature inside the refrigerator.

Causes of a bad gasket assembly can include wear and tear over time, damage from frequent opening and closing of the door, or degradation from exposure to various elements. A compromised gasket can lead to inefficiency in the refrigerator's cooling performance.

Symptoms of a bad gasket assembly include:

• Warm air entering the refrigerator
• Increased energy consumption
• Frost buildup inside the refrigerator
• The door not sealing properly or being difficult to close

This OEM LG part is also compatible with Sears/Kenmore models.

The Door Gasket Assembly is an OEM replacement part for LG refrigerators. This part seals the door and maintains a thermal barrier. Proper compression provides energy efficiency.

Causes of a faulty gasket assembly may involve deterioration as adhesive softens from repeated compression. Mineral deposits accumulated over extended use could also harden material reducing flexibility.

Symptoms of a problematic gasket include:

• Cool air felt leaking from the door
• Moisture visible on seal interface areas
• Temperature fluctuations

This part is also compatible with some Kenmore refrigerator models.

The Water Valve Assembly is an OEM part for LG refrigerators. It controls the flow of water into the refrigerator's ice maker and water dispenser, ensuring a steady and controlled supply. This valve opens and closes in response to electrical signals from the refrigerator, allowing water to enter the appropriate compartments for ice making and dispensing.

Over time, the water valve can wear out or become damaged due to mineral deposits, wear and tear, or electrical issues. A malfunctioning water valve can lead to problems such as water not dispensing correctly or the ice maker not producing ice.

Symptoms of a bad water valve assembly include:

• No water dispensing from the refrigerator
• Ice maker not producing ice
• Leaking water from the valve area
• Unusual noises coming from the valve

This OEM LG part is also compatible with Sears/Kenmore.

This rail guide assembly supports and guides a sliding refrigerator drawer, helping it open and close smoothly. Replace a cracked or worn guide to restore proper alignment and prevent binding or the drawer jumping off its track.

• Provides the track and support for pantry/crisper/freezer drawer movement
• Keeps the drawer aligned to reduce wobble and uneven travel
• Restores smooth open/close when the guide is cracked or worn
• Helps the drawer seat fully for a proper fit

• Unplug the refrigerator before servicing
• Remove the bin/drawer from the compartment to access the guide
• Save and reuse existing mounting hardware and spacers
• Install the new guide, align the drawer, and verify smooth travel

This drain tube assembly channels defrost water from the evaporator to the drain pan, preventing leaks and water buildup. Replace a cracked or clogged tube to restore proper drainage and reduce puddles or ice inside your refrigerator.

• Directs defrost water from the drain outlet to the drain pan
• Helps prevent water leaks inside the fresh food or freezer compartment
• Addresses issues from a tube that is cracked, kinked, or obstructed by debris/ice
• Common symptoms: water under crisper drawers, puddles beneath the unit, or ice forming at the freezer bottom

• Unplug the refrigerator before servicing
• Access the drain outlet and remove any ice or debris from the drain path
• Fully seat the tube at both ends to ensure a secure, leak-free fit
• Test by pouring a small amount of warm water into the drain to confirm proper flow to the pan

This is a refrigerator drawer guide assembly that supports and guides a crisper/vegetable bin so it slides smoothly in and out. Replacing a worn guide restores proper drawer alignment and easy operation.

• Provides the track surface for the vegetable/crisper drawer
• Helps correct sticking, binding, or a sagging/misaligned drawer
• Can reduce scraping noises and uneven drawer movement
• Restores smooth sliding action after wear or damage

• Unplug the refrigerator before service
• Remove the affected drawer and any shelf above it for access
• Retain and transfer any screws or clips from the original guide
• Test drawer movement and alignment before closing up

This button lever is the small plastic actuator behind a push button that engages the internal latch or switch. Replace it to restore clean, reliable operation when the button sticks, feels loose, or no longer triggers the function.

• Links the external push button to an internal latch or microswitch so the feature operates
• Transfers motion smoothly and helps the button return after pressing
• Common failure points include cracked pivots, broken tabs, or worn contact surfaces
• Symptoms: button sticks, feels mushy or loose, requires extra force, or fails to activate

• Unplug the appliance or disconnect power before servicing
• Use your model's exploded view to access the button area and note lever orientation
• Release retaining tabs carefully; transfer any springs or clips from the old lever if reused
• Test button action before final reassembly

Door gasket assembly provides a secure, flexible seal around the appliance door to prevent leaks and maintain proper internal conditions. Replacing a torn or worn gasket restores sealing performance and reduces leaks, drafts, or temperature loss. What it does:

• Forms the primary seal around the door to keep water, air, and temperature inside the appliance.
• Stops visible leaks or pooling around the door opening.
• Helps prevent temperature fluctuations, frost buildup, or loss of cleaning/drying performance caused by a poor seal.
• Addresses visible damage symptoms such as cracks, tears, deformation, or persistent odors around the door edge.

• Always disconnect power (and water, if applicable) before starting any repair.
• Remove the old gasket carefully; inspect and clean the door channel and mounting surface before installing the new gasket.
• Ensure the replacement gasket is fully seated and any retaining clips or fasteners are secured per OEM instructions; test the door for proper fit and sealing.

This door gasket assembly seals the refrigerator door to help maintain proper internal temperature and reduce energy loss. Replacing a worn or torn gasket restores a tight seal for better cooling and food preservation. What it does:

• Forms an airtight seal between the refrigerator door and cabinet to limit warm air entry
• Helps prevent frost buildup and condensation that can occur with a failing seal
• Reduces compressor run time caused by air leaks, improving cooling consistency
• Commonly replaced when gasket is torn, deformed, hard, or no longer seats properly

• Disconnect power to the appliance before starting any repair.
• Inspect the door edge and mounting channel; remove any debris before seating the new gasket.
• Warm the gasket slightly if needed to help it seat; avoid open flames or overheating.
• Verify even seating around the entire door and check door alignment; run a paper test to confirm a consistent seal.

This case assembly is the outer housing for the Magic Room compartment, restoring proper fit and protection for internal components. Replaces a cracked, warped or damaged compartment case to help maintain compartment integrity and appearance. What it does:

• Provides the structural housing for the Magic Room compartment and secures internal components
• Restores proper alignment and fit to prevent rubbing or interference with doors/drawers
• Helps maintain an even internal compartment environment by sealing the compartment area
• Addresses visible damage such as cracks, broken mounting tabs or deformation

• Refer to the refrigerator's service manual for disassembly/reassembly steps and proper fastener torque
• Disconnect power to the appliance before starting any repair to avoid electrical hazard
• Handle plastic components carefully to avoid further cracking; replace any broken mounting clips
• Replace damaged screws or brackets with OEM-specified hardware for a secure fit

This damper controls airflow between compartments to help maintain proper temperatures and consistent cooling. It replaces a worn or broken damper to restore normal airflow and temperature balance inside the appliance. What it does:

• Regulates air flow between compartments so the refrigerator can maintain set temperatures
• Helps reduce uneven cooling and temperature swings caused by a stuck or broken damper
• Works as part of the appliance's air distribution system to route cooled air where needed
• Common symptom: compartment temperature too warm or inconsistent airflow noise from the damper area

• One damper assembly

• High-level replacement; access usually requires removing interior panels or duct covers
• Disconnect power before any repair to avoid shock or injury
• Handle with care to avoid bending or damaging mounting tabs and linkage

This cover assembly protects the machine components and helps keep internal machinery free of debris and accessible for repair. It provides a durable barrier that helps extend component life and maintains safe operation. What it does:

• Shields motors, belts and internal linkages from dust and lint that can cause wear
• Helps contain moving parts to reduce pinch or contact hazards during normal use
• Maintains proper component alignment by providing a stable mounting surface
• Commonly replaced when cracked, warped, missing fasteners, or damaged from impact

• One cover assembly as shown

• Disconnect power before attempting service
• Handle gently to avoid cracking plastic tabs; inspect mounting clips and screws for damage
• Reuse original fasteners only if undamaged; replace any stripped screws or broken clips

This front plate assembly replaces the damaged or worn front-facing plate on compatible LG appliances, restoring the unit's appearance and protecting internal components. It's a direct-fit exterior panel used where the front surface is cracked, dented, or missing. What it does:

• Covers and protects internal components behind the appliance's front area
• Restores a uniform exterior finish and eliminates gaps or exposed parts
• Helps maintain proper alignment of adjacent trim and controls
• Suitable when the visible front surface is cracked, dented, or cosmetically damaged

• One front plate assembly as shown

• Installation typically requires removing adjacent trim and fasteners
• Handle edges carefully and support the assembly to avoid scratching finishes
• Disconnect power to the appliance before beginning work to prevent injury
• If clips or screws from the original assembly are worn or missing, replace them with OEM-specified fasteners

This filter cover replaces the damaged or worn cover that holds the air filter in place, helping maintain correct filter position and airflow for proper operation. It's a direct-fit replacement designed for easy swap-out. What it does

• Secures and protects the air filter inside the unit so the filter seals and sits correctly.
• Maintains proper airflow path to help the system run as designed.
• Prevents debris from bypassing the filter and entering internal components.
• Helps reduce rattling or vibration caused by a loose or broken cover.
• Restores the intended fit and finish of the filter compartment.

• One filter cover

• Disconnect power or remove batteries before removing the old cover to avoid fan or electrical hazards.
• Remove the old cover by releasing clips or screws; align replacement and engage clips or reinstall screws securely.
• Do not force the cover—ensure filter is seated correctly before closing to avoid damage.
• Replace hardware with OEM-equivalent parts for proper fit.

This drip tray catches and channels water runoff inside the appliance to help prevent pooling and minor leaks. It's a direct-fit replacement listed by the manufacturer and sold as the single tray used in the unit. What it does

• Collects condensate or defrost water and directs it to the drain area to prevent pooling.
• Helps stop water from dripping onto lower drawers, shelves or the floor.
• Commonly replaces a cracked, warped or missing tray that causes visible leaks or water buildup.
• Fits into the appliance's lower compartment where the original tray sat.

• Unplug the appliance or disconnect power before servicing.
• Remove any obstructing drawers or shelves to access the tray location; handle glass shelves carefully.
• Lift out the old tray and set the new tray into the same position; no special tools typically required.