79573163160 Parts

The Drier Assembly is an OEM part for LG refrigerators. This part is responsible for removing moisture and contaminants from the refrigerant. This ensures that the refrigerant circulates effectively and efficiently, preventing damage to other components and maintaining the refrigerator's cooling performance.

Causes of a bad Drier Assembly can include contamination from moisture entering the refrigerant lines, blockages from debris or particulates, and general wear and tear over time that reduces its effectiveness.

Symptoms of a bad Drier Assembly include:

• Reduced cooling efficiency or warm refrigerator temperatures
• Unusual noises from the refrigeration system
• The compressor running continuously or cycling frequently
• Frost buildup on the evaporator coils due to improper refrigerant flow

This OEM LG part is also compatible with Sears/Kenmore models.

This door stopper mounts at the hinge to limit the refrigerator door's opening angle and provide a positive stop. Replacing a worn stopper helps protect the hinge, prevent over-swing, and promote a smooth, even door seal.

• Limits door opening at the hinge to prevent overextension
• Helps maintain door alignment and consistent gasket contact
• Reduces impact that can loosen hinges or damage the cabinet
• Common symptoms: door swings too far, clunks at full open, doesn't stop smoothly, or shows visible wear at the stop

• Disconnect power and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners as needed to access the stopper
• Install the new stopper in the same orientation; tighten hardware securely
• Verify door swing and sealing after reassembly

This AC motor powers the appliance's fan or blower to move air through the system. Replacing a worn motor restores proper airflow to support cooling/ventilation and protect internal components from overheating. What it does:

• Rotates the fan/blower to circulate air through the appliance
• Helps maintain proper temperatures and component cooling
• Common failure signs: fan won't start, starts then stalls, weak airflow, loud humming/grinding, overheating or safety shutoffs
• Often required when motor bearings seize or windings fail

• 1 AC motor

• Disconnect power and allow hot components to cool before servicing
• Note wire positions; transfer any brackets, grommets, or the fan blade from the original motor if reused
• Clear debris and restore power and verify smooth, quiet airflow

This rail guide assembly supports and aligns a refrigerator drawer so it slides smoothly along its track. Replacing a worn rail restores easy operation and helps prevent binding, sagging, or uneven travel when opening and closing.

• Supports and guides the drawer/bin along the cabinet track
• Helps the drawer open and close smoothly and stay level
• Maintains proper alignment so the drawer seats correctly
• Common symptoms: drawer hard to slide, tilts or binds, rough/noisy travel, visible cracks or damage on the rail

• Disconnect power and remove drawer contents for safety
• Pull out and lift the drawer/basket off the rails to access the mounting points
• Remove screws/clips, transfer any brackets or end caps from the old rail, and install the new assembly
• Re-engage the drawer on both rails and test for smooth operation before reloading

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This turntable roller ring sits under the glass tray and allows it to rotate smoothly for even heating. Replace a worn, warped, or broken ring to restore stable rotation and consistent cooking performance.

• Supports the glass turntable and rides on built-in rollers for smooth, quiet movement
• Keeps the tray level and centered to promote even heating
• Common symptoms: tray not turning, uneven cooking, scraping/grinding noises, or a wobbly/slipping turntable
• Restores proper interaction between the turntable, drive coupling, and motor

• Unplug the microwave or switch off the breaker before servicing
• Remove the glass tray; lift out the old ring and clean the track
• Place the new ring with the rollers facing down on the track; reseat the tray on the center drive coupling
• Test rotation with a microwave-safe cup of water

This refrigerator door bin mounts to the inside of the door to hold bottles, jars, and condiments. Replacing a cracked or missing bin restores secure storage and helps prevent items from tipping or falling when the door opens.

• Provides organized, convenient storage on the door for frequently used items
• Attaches securely to molded tabs/rails on the inner door panel
• Helps prevent tipping and spills as the door opens and closes
• Common symptoms: cracked bin, broken locking tabs, won't stay seated, falls off the door

• Unplug the refrigerator or switch off power at the breaker before starting
• Remove contents, then lift the old bin straight up to disengage from the door
• Align the new bin's hooks with the door slots/rails and press down until fully seated
• Verify a snug fit before reloading items

This plastic tube carries water within your refrigerator between internal components. Replacing a brittle, kinked, or leaking line restores dependable water flow and helps prevent drips that can damage interiors, cabinetry, or floors. What it does

• Routes water between internal components (such as valves, filters, reservoirs, and dispensers)
• Helps maintain proper water flow and pressure when intact and unkinked
• Typical failure symptoms: water leaks, slow or no water flow, visible cracks, flattening, or kinks
• Age- or heat-related hardening can cause stress cracks near bends or fittings

• One plastic tube

• Unplug the refrigerator and shut off the water supply before servicing
• Note original routing and clip locations; avoid sharp bends, abrasion points, and hot surfaces
• Insert tube ends fully into their fittings (quick-connect or compression, per design) and gently tug to confirm they're seated
• Restore water, purge air as needed, and check all joints for leaks before pushing the unit back

The Motor is an OEM component specifically designed for LG refrigerators. It houses the evaporator fan motor located inside the refrigerator housing. 

This evaporator fan motor circulates cool air within the refrigerator compartment, ensuring consistent temperatures are maintained. It actively distributes cold air produced by the refrigeration system throughout all shelves and drawers inside the refrigerator. 

Causes of a bad evaporator motor can include normal wear and tear over time, failures in the motor's electronic components, or damage from impact or water damage. 

Symptoms of a bad evaporator motor include:

• Inconsistencies in interior temperatures   
• Warm or cool spots developing on refrigerator shelves 
• Abnormal noises coming from inside refrigerator walls
• The fan motor fails to start or run intermittently 

Replacing the evaporator motor with this genuine LG OEM part restores proper air circulation. It is also compatible with Sears/Kenmore refrigerator models.

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This is a ring intended for use in refrigerators. The ring is used to adjust the height of the door. Genuine OEM replacement rings are necessary for the repair to ensure a proper fitting.If the refrigerator door no longer opens or closes easily, or if it is not sealing properly, the rings may need to be replaced. Visual inspection can determine if there are problems with the refrigerator door rings. Make sure to unplug the device before starting any of the disassemblies of the machine. Wear gloves.This ring is an authentic OEM replacement part. It is sold as an individual unit. The ring is made of high-quality, durable materials. The replacement piece is sourced directly from the manufacturer. It can be installed in several models of refrigerators. The genuine OEM replacement ring is compatible with refrigerators produced by both LG and Kenmore.

This drawer tray assembly forms the shelf/frame that supports and guides a refrigerator drawer. Replacing a damaged tray restores smooth drawer operation and secure storage so bins slide correctly and items are held level.

• Provides the fixed frame the drawer rides on and supports the weight of stored items
• Keeps the drawer aligned on its tracks for easy opening and closing
• Maintains proper spacing and organization within the compartment
• Typical symptoms: cracked or broken frame/tabs, sagging drawer, binding, or falling off track

• Disconnect power and remove food from the affected area
• Slide the drawer(s) out and lift out the damaged tray
• Seat the new tray assembly fully on locator tabs/rails; avoid forcing cold, brittle plastic
• Reinstall the drawer(s) and verify smooth movement

This door stopper assembly mounts at the hinge to control how far the door opens and promote smooth, consistent closing. Replacing a worn or broken stopper restores proper door swing and helps protect the hinge from overextension.

• Limits the door's opening range to prevent overextension
• Guides and cushions door movement for a smoother close
• Helps maintain door alignment at the hinge area
• Common symptoms: door swings too far, doesn't stop at the usual angle, clicks/binds near the hinge, or visible cracks/wear on the stopper

• Disconnect power to the appliance before servicing
• Support the door and use a helper when loosening hinge hardware
• Note the original orientation and transfer any spacers/shims if present
• Tighten fasteners evenly and verify smooth door operation before finalizing reassembly

The Magnet Switch is an OEM part for LG refrigerators. It plays an important role in monitoring the position of the refrigerator door. 

The magnet switch works together with a magnet installed in the door gasket to detect when the door is opened or closed. It communicates this information to the control board which uses it to manage temperatures and fan speeds accordingly. 

Causes of a bad magnet switch can include wear and tear over time, physical damage, or failure of internal components. 

Symptoms of a bad magnet switch include:

• Improper cooling and freezing performances 
• Inability to detect when the door is opened
• Erratic temperature fluctuations
• Errors codes relating to door sensors

This genuine OEM LG magnet switch restores the door monitoring functions of your refrigerator. It is also compatible with Sears/Kenmore refrigerator models.

This is a refrigerator door basket that mounts on the inner door liner to hold bottles, condiments, and other small items. Replacing a damaged bin restores secure storage and helps keep items organized and accessible.

• Provides on-door storage space for beverages and condiments
• Helps keep items from tipping or falling when the door opens
• Replace if cracked, broken, warped, or no longer stays seated in the door slots
• Common signs include the bin falling off, visible cracks, or reduced capacity

• Unplug the refrigerator for safety before replacing interior parts
• Lift the old bin up and out of the door liner slots
• Align and press the new bin straight into the slots until fully seated
• Do not overload; distribute weight evenly to prevent future damage