7957756 Parts

This hinge cover fits over the door hinge to conceal and protect the mechanism. Replacing a cracked or missing cover restores a clean, finished look and helps keep hinge components shielded from dust, snags, and everyday wear.

• Conceals the door hinge for a finished, factory look
• Helps protect hinge hardware from dust and accidental contact
• Reduces snag points around the hinge area
• Typical failure signs: cracked plastic, broken tabs, missing cover, or a cover that won't stay attached

• Disconnect power before servicing; hinge areas can contain wiring
• Open the door and remove any retaining screw(s) or release the cover's tabs
• Lift off the old cover; align and snap or screw the new cover into place
• The door opens and closes freely with the cover installed

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and warm, moist air out. Restores proper sealing to help maintain temperature and reduce frost or moisture buildup. What it does:

• Seals the refrigerator door to maintain consistent internal temperatures
• Helps prevent moisture, frost, and condensation inside the fresh-food compartment
• Reduces air leaks that can cause the fridge to run more frequently or uneven cooling
• Common symptom: visible gaps, torn or compressed seal, or moisture/frost near the door edge

• Disconnect power to the appliance before starting any work.
• Remove the old gasket carefully; inspect and clean the gasket channel and mating surface before installing the new seal.
• Warm the gasket slightly or work around the perimeter to seat it evenly; avoid overstretching.
• If clips or adhesive are used on your model, reuse or replace only the exact fasteners specified by the manufacturer.

This refrigerator sheath heater melts frost from the evaporator so air can circulate freely and the unit can cool properly. Replacing a failed heater helps restore even temperatures and reduce frost buildup in the freezer.

• Warms the evaporator coil during defrost cycles to clear ice
• Helps prevent restricted airflow, warm spots, and long run times
• Common failure symptoms include heavy frost on the evaporator, poor cooling, ice buildup on the back panel, or frequent defrost errors
• May cause sizzling sounds or water under the evaporator area during normal operation after replacement

• Unplug the refrigerator before service; defrost any heavy ice to access parts safely
• Access typically from the rear of the freezer compartment behind the evaporator cover
• Handle heater leads and evaporator fins carefully to avoid damage
• Secure all connectors before reassembly

A momentary push-button switch that restores reliable button control on the appliance console. Replaces a worn or non-responsive push switch so the control board receives a clear input when the button is pressed. What it does:

• Sends a momentary electrical signal to the control board when pressed
• Replaces broken, stuck, or intermittently working push buttons
• Helps resolve symptoms like no response from the console, intermittent button function, or a physically damaged button
• Functions as the user input for single-press commands

• One momentary push switch

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control panel or console; use appropriate screwdrivers
• Note connector orientation and gently unplug wire harness—do not pull on wires

This center hinge assembly replaces the refrigerator door center hinge to restore proper door alignment and smooth operation. It supports the door weight and helps maintain correct sealing for reliable cooling performance. What it does:

• Supports the center of the door, keeping it aligned and preventing sagging
• Provides the pivot point for smooth opening and closing
• Helps maintain a consistent door seal to prevent cool-air loss
• Can eliminate shifting, squeaking, or uneven door gaps caused by a worn hinge

• 1 center hinge assembly

• Disconnect power and empty or support the door before removing the hinge
• Use appropriate tools and a second person to safely support the door during replacement
• Inspect adjoining hinges and mounting hardware; replace any damaged fasteners for best results

This cover cap is a small plastic trim piece that protects exposed fasteners and improves the appliance's appearance. It snaps into place to hide mounting posts and help prevent snags or debris buildup. What it does:

• Covers and protects exposed screws, posts, or fasteners for a finished look
• Prevents lint, dust, and debris from collecting around the mounting point
• Reduces the chance of fabric snags or contact with sharp edges
• Restores worn or missing trim for improved cosmetics

• Disconnect power to the appliance before starting any service that exposes electrical components
• Usually installs by snapping over the post or press-fitting into the trim opening — no special tools required
• If needed, remove adjacent trim pieces to gain access, then reinstall trim in reverse order
• Inspect surrounding mounting hardware for damage and replace if necessary

This center hinge assembly supports and pivots the middle door section to keep doors aligned and operating smoothly. Replace a worn or damaged center hinge to restore proper door movement and help maintain a tight seal. What it does:

• Provides the pivot point and structural support for the center door section to open and close smoothly
• Helps maintain door alignment to prevent rubbing, scraping, or uneven gaps
• Reduces door sag that can interfere with sealing and cooling efficiency
• Prevents binding or sticking during door operation

• One center hinge assembly

• Disconnect power to the appliance before starting any repair
• Doors are heavy—have a second person assist to support doors while removing or installing the hinge
• Remove any trim or covers to access hinge screws; align doors fully before tightening fasteners
• Use manufacturer-recommended torque; do not overtighten screws or force parts into place

This is a replacement mounting screw used to secure appliance panels, trim or components. It restores proper attachment to reduce vibration and rattling and helps keep removable parts firmly in place during operation. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Restores secure fit when original screw is missing, loose, or stripped
• Reduces rattling and vibration caused by loose hardware
• Helps maintain proper alignment of removable covers and control panels

• Disconnect power and water before starting any repair
• Verify size and thread match the original screw before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not overtighten — overtightening can strip threads or crack plastic parts
• Keep small parts away from children and pets

This cover panel replaces a damaged or missing exterior trim piece to restore the appliance's appearance and protect internal components from dust and debris. It fits where the original cover was mounted and keeps wiring and parts shielded. What it does

• Covers and protects internal components from dirt and accidental contact
• Restores the appliance's exterior finish for a clean, finished look
• Helps reduce rattles by securing loose openings or edges
• Matches the original mounting locations for proper fit and alignment

• Disconnect power (unplug appliance or switch off breaker) before starting work.
• Removal/install typically requires basic tools (screwdriver or nut driver); keep original fasteners unless replacements are provided.
• Handle with care to avoid scratching the finish or breaking mounting tabs; avoid forcing clips.

This replacement hinge cover is a molded trim piece that snaps over the refrigerator door hinge to restore the appearance and protect the hinge area from dirt and damage. It keeps the hinge assembly concealed and the door looking finished. What it does:

• Covers and protects the door hinge assembly from dust, grease and accidental contact
• Restores a clean, finished look when original hinge cover is cracked, broken or missing
• Helps prevent debris buildup that can interfere with hinge movement
• Matches original mounting style for a secure snap-on fit when intact

• High-level replacement: typically snaps into place; inspect clips/tabs and align before pressing fully
• Power/disconnect: no electrical disconnect usually required, but follow appliance safety guidance and keep doors supported
• Handle gently to avoid breaking plastic clips during installation

A replacement cover bar that restores the appliance's exterior trim and protects the underlying components from dirt and damage. Ideal for repairing visible cracks, breaks or missing trim to improve appearance and function. What it does

• Covers and protects the edge of the cabinet or control area to prevent debris from entering.
• Restores a finished look to cracked, broken or missing trim pieces.
• Helps keep internal components shielded from accidental contact and light moisture.
• Useful when original trim is warped, split, or cosmetically damaged.

• Disconnect power to the appliance before beginning any repair.
• Installation typically requires a screwdriver; keep removed fasteners for reuse.
• Handle the trim gently to avoid cracking; align tabs/slots before fastening.
• Replace missing or damaged mounting hardware or clips to ensure a secure fit.

This replacement door handle restores a secure grip and proper door operation on compatible refrigerators. Durable and contoured to match factory styling, it replaces cracked, loose, or broken handles for a safer, finished look. What it does:

• Provides a firm, ergonomic grip to open and close the refrigerator door
• Replaces cracked, damaged, or loose handles that affect door usability
• Restores the appliance's factory appearance and user comfort
• Helps prevent further damage from using a compromised handle

• Power off and unplug the appliance or disconnect power at the breaker before installation to avoid electrical risk
• Use appropriate hand tools; support the door during removal/installation to prevent injury or damage
• Follow the manufacturer service manual or on-page model fitment for proper screw locations and torque