79578002211 Parts

This is the DC motor that drives the condenser fan, typically located near the compressor at the bottom rear of the refrigerator. It circulates air across the condenser coils to dissipate heat and maintain efficient cooling. Replace this motor if the refrigerator is running warm, the compressor is overheating, or the fan is not spinning when the compressor is operating.

Center hinge assembly supports your refrigerator door at the middle pivot point for proper alignment and smooth operation. Replace if door sags or won't seal.

This is a defrost temperature sensor that monitors evaporator coil temperature and signals the defrost control board to initiate or end defrost cycles. It helps prevent excessive frost buildup on the evaporator, ensuring proper cooling performance. Replace this sensor if the refrigerator is not cooling properly, frost is accumulating heavily on the evaporator coils, or the unit is running continuous defrost cycles.

Upper hinge assembly supports and pivots your refrigerator door. Replace if your door sags, won't close evenly, or makes noise. Verify fit with model number.

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

Small stopper that fits inside the handle assembly to limit travel and keep the handle properly seated. Replace if worn, missing, or broken to restore secure feel.

Display not working or showing incorrect temperature? This refrigerator display control board manages temperature settings and interface functions.

The refrigerator door stop guide is a small bracket or track component that controls how far your refrigerator door swings open and keeps it from opening too wide. It protects the door hinges, shelves, and walls from damage caused by the door swinging freely. Replace this part if your refrigerator door swings open too far, feels uncontrolled, or if the existing guide is cracked or broken.

Mounts on the shutter damper mechanism to adjust airflow settings. Replace a cracked, loose, or missing knob to restore smooth control and a finished look.

Secure refrigerator components with this mounting screw. Replaces missing, stripped, or corroded fasteners. Restores tight fit and alignment.

The Door Basket is an OEM accessory specifically designed for LG refrigerator doors containing vegetable drawers. This hanging basket provides auxiliary storage directly above crisper bins.

Causes of a bad door basket can include wear and tear over time compromising the mesh material, or damage from overloading reducing structural integrity.  

Symptoms of a bad door basket include:

• Holes or tears reducing usable capacity   
• Detached fasteners slipping off mounting brackets
• Warped contours no longer remain properly installed
• Insecure attachment inhibiting safe door openings  

Replace yours today with this genuine OEM LG basket to maximize organizational convenience. Sturdy brackets produce a snug, stable fit. Compatible with Samsung, GE, and Frigidaire refrigerators featuring dual-drawer doors, this upgrade complements any modern kitchen setup. Reliable performance preserves aesthetic appeal.

This is the rubber door gasket (seal) that lines the edge of the freezer door on a refrigerator. It creates an airtight seal when the door is closed to maintain proper temperature and prevent cold air from escaping. Replace this gasket if you notice frost buildup inside the freezer, the door does not seal tightly, or if the gasket is torn, cracked, or warped.

This is a small retainer clip that secures the compressor in place at the base of the refrigerator. It helps prevent the compressor from shifting or vibrating excessively during operation. Replace this clip if your refrigerator produces unusual rattling or vibrating noises from the back, or if the compressor appears loose or has shifted from its mounting position.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit