79578002211 Parts

This customized screw is the manufacturer-specified fastener used to secure appliance components and panels at their mounting points. Replace a missing, stripped, or corroded original to restore a tight fit, proper alignment, and help eliminate vibration or rattling.

• Secures brackets, covers, and panels to the chassis at designated mounting points
• Maintains alignment and stability of the assembly during operation
• Helps address loose or rattling components caused by a missing or damaged fastener
• Direct replacement for the original fastener used in the specified location

• Disconnect power; shut off water before servicing
• Match head/length to the original; transfer any original clips or washers if used
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten until snug—do not overtighten into plastic or thin sheet metal

This harness assembly routes power and signals between appliance components to restore electrical connections and normal operation. It replaces damaged or frayed wiring to stop intermittent power, control failures, or no-start conditions. What it does:

• Reconnects power and control circuits between major components
• Replaces damaged, burned, or frayed wires and connectors that cause intermittent or lost function
• Restores reliable signal paths to controls, sensors, and motors
• Helps resolve symptoms like sporadic operation, failure to start, or component non-response

• Disconnect power to the appliance before accessing electrical components.
• Match connectors and wire routing to the original harness during installation to avoid pin miswiring.
• Inspect connector pins and mating terminals for damage; replace the harness if pins are bent or corroded.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

The Lower Hinge Assembly is an OEM part for LG refrigerators. This lower hinge safely and smoothly supports the weight of the refrigerator door.

Causes of a bad lower hinge can include loose or worn parts from years of use, damage from overloading doors with heavy items, or failure due to impact or bending stresses.  

Symptoms of a bad lower hinge include:

• Doors sagging or dropping over time
• Noisy squeaks or grinding sounds coming from hinges
• Difficulty opening and closing doors smoothly  
• Doors unable to stay open at various angles

Replace yours today with this genuine OEM LG assembly before further issues develop. This replacement part is compatible with Frigidaire, Samsung, and Kenmore models for a factory fit and function.

This replacement shelf glass restores a flat, sturdy surface inside your refrigerator for safe, organized food storage. Replace cracked, missing, or unstable glass to help contain spills and return your shelf to full strength.

• Provides a level, load-bearing surface for food containers in the compartment
• Helps contain leaks and spills so messes don't spread below
• Replace when glass is cracked, chipped, shattered, bowed, or missing
• Restores lost storage space and improves shelf stability

• If handling broken glass, unplug the refrigerator and wear cut-resistant gloves and eye protection.
• Remove items from the shelf, slide out the shelf/assembly, and carefully lift out the old glass.
• Clean any debris from the frame or supports. Set the new glass in place, ensuring it seats fully and is secure before reinstalling.

This vegetable tray stores and organizes produce in the refrigerator's fresh-food compartment. Replacing a cracked or missing bin restores usable space and smooth sliding access so fruits and vegetables stay contained and easy to reach.

• Holds fruits and vegetables in the crisper area
• Slides in/out on existing drawer rails for convenient access
• Helps keep items separated and contain minor spills
• Common symptoms: cracked or broken bin, missing tabs, drawer won't slide smoothly or stay seated

• Remove contents and slide the old drawer straight out
• Align the new drawer with the existing rails and push in until fully seated
• Handle nearby glass shelves carefully to prevent chips or breakage
• Disconnect power before working inside

Restore usable, level storage space with this Refrigerator Shelf Assembly. It replaces a damaged or missing shelf in the fresh food compartment, helping keep items organized and properly supported so you can make full use of your refrigerator.

• Provides a flat, sturdy surface for storing food and containers
• Replaces shelves that are cracked, shattered, sagging, or missing
• Helps prevent items from tipping and maintains interior organization
• Common signs: broken glass or frame, shelf won't seat in side rails, or slides out

• Remove food from the area and open the door fully
• Lift/tilt the old shelf to release it from the side rails and slide it out
• Align the new shelf with both rail grooves and push in until fully seated
• Handle glass carefully and wear cut-resistant gloves

This cover support bracket secures an appliance cover or panel, restoring proper alignment and stability. Replacing a damaged support helps eliminate rattles and gaps so the cover seats correctly and stays in place.

• Provides structural support for the associated cover/panel
• Keeps the cover aligned and firmly seated against the cabinet
• Replaces a cracked, stripped, or missing support
• Symptoms include a loose or sagging cover, vibration/rattling noises, or covers that won't stay attached

• Disconnect power before servicing; allow any hot surfaces to cool and wear cut-resistant gloves
• Remove the cover/panel to access the support and retain all mounting hardware
• Install the new support, transferring screws or clips as needed
• Reinstall the cover and verify proper fit before restoring power

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This freezer shelf assembly replaces a damaged or missing shelf to restore usable storage space and stable support for frozen items. It fits into freezer compartment shelving tracks and provides a flat, secure surface. What it does

• Replaces a broken, cracked or warped freezer shelf so food and containers sit level and stable
• Restores organized storage when an existing shelf is bent or missing
• Helps prevent items from tipping or spilling inside the freezer
• Matches OEM fit and mounting points for straightforward shelf support

• One freezer shelf assembly

• Remove food and unplug or switch off the appliance power before starting work
• Shelf typically slides or snaps into place on existing shelf supports; no special tools usually required
• Handle shelf carefully to avoid sharp edges on broken plastic or glass
• If mounting clips or supports are damaged, replace them before installing the new shelf

This inner door shelf replaces a cracked or broken refrigerator door basket so you can safely store bottles and small items. It restores secure storage and keeps the door organized without rattling or falling items. What it does

• Replaces a damaged or cracked door basket that no longer holds items securely
• Restores proper storage on the refrigerator door and prevents items from slipping or falling
• Reinstates mounting stability if original shelf tabs were broken or worn
• Reduces rattling and improves overall organization inside the door

• Unplug the appliance or disconnect power before starting any repair
• Empty the door compartment and remove any remaining clips or fasteners from the old basket
• Align the replacement basket with the door mounting points and snap or slide into place until securely seated
• If mounting tabs are broken, inspect adjacent hardware and replace any additional damaged clips before use

The Drain Tube Assembly is an OEM part for LG refrigerators. This drain tube assembly is responsible for directing condensation and melt water that accumulates in the refrigerator away to the evaporator pan.

Causes can include cracks developing from limescale or mineral accumulation, flexing fatigue from repeatedly catching drips, or damage from improper cleaning methods.

Symptoms of a bad drain tube assembly include:

• Puddles or leaks developing underneath the refrigerator
• Poor air flow from vents and higher temperatures
• Ice or moisture buildup in refrigerator walls and seals
• Water stains or corrosion appearing inside the unit

This OEM LG part is also compatible with some Kenmore models.

This control case assembly is the replacement outer housing that holds and protects the appliance control board and user interface, restoring a secure fit and proper button/panel alignment for safe operation. What it does:

• Houses and protects the control board and associated electronics from dust, moisture, and accidental contact
• Keeps control panel buttons and switches properly aligned for reliable user input
• Prevents loose or rattling control components that can cause intermittent operation or noise
• Supports the front panel and display mounting for normal appearance and functionality

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Handle the control board and connectors carefully; avoid touching circuit traces or components.
• Basic hand tools are typically required to remove the panel and transfer the control board into the new housing.
• If the control board is damaged or shows corrosion, this part replaces only the housing unless otherwise specified.

This handle assembly replaces a damaged or worn refrigerator door handle to restore safe, reliable grip and smooth door operation. It provides a direct-fit replacement to help you open and close the door securely. What it does:

• Replaces a cracked, broken, loose, or missing refrigerator door handle
• Restores a solid grip and proper leverage for opening and closing the door
• Helps prevent further damage to the door trim from makeshift handles
• Supports correct door alignment and user control during normal use

• Use basic hand tools; avoid overtightening fasteners to prevent damage
• If accessing electrical components, unplug the appliance or turn off power at the breaker before beginning
• Keep removed fasteners and parts in a safe place for reassembly