970C503220 Parts

These components provide stable support and vibration dampening for washers mounted on pedestals, located at the base where the washer connects to the pedestal. Replace when experiencing excessive vibration, movement during operation, or visible wear on the bushings.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

Secures the fan housing to its mounting points. Replace if the clip is broken, missing, or worn to eliminate rattles and prevent air leaks in your dryer.

This is a heat shield insulator that mounts on the inner side of the dryer door in a stacked laundry center or washer/dryer combo unit. It prevents excessive heat from transferring through the door during drying cycles, protecting the outer door surface and improving energy efficiency. Replace this insulation if it is torn, deteriorated, or missing, which can cause the door to become excessively hot to the touch or reduce drying performance.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

Fix a washer that won't advance through cycles or stays stuck on one setting. This mechanical timer restores proper cycle sequencing. 1-hour DIY repair.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

Self-leveling leg pad for washers and laundry appliances. Replace worn, cracked, or missing pads to stabilize your unit and protect flooring.

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.

Secures the top or front panel to your laundry center frame. Replace if bracket is cracked, broken, or missing to restore proper panel alignment.

Ceramic dryer heating element terminal block.