Ade3srgs175two1 Parts

This dryer steam nozzle directs steam into the dryer drum to help remove wrinkles and refresh fabrics. It replaces a worn or damaged nozzle to restore proper steam flow and steaming performance. What it does:

• Channels steam from the boiler/steam supply into the drum for wrinkle-release and fabric refreshing
• Helps ensure steam is delivered where intended instead of leaking or dispersing inefficiently
• Supports normal dryer steam functions when installed correctly

• One dryer steam nozzle

• Install only after disconnecting power and shutting off steam/water supply; follow OEM service instructions
• Inspect surrounding fittings, hoses, and gaskets for wear and replace if needed
• Use appropriate tools and torque; avoid overtightening which can crack plastic or damage threads

This is a 8-16 x 5/8 tapping screw with a #6 Phillips drive, used to fasten panels and components on compatible appliances. It provides a secure, low-profile hold for trim, brackets and covers. What it does:

• Secures panels, trim pieces, brackets or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment and fit of exterior or interior panels
• Provides a threaded connection in sheet metal or tapped holes

• Use the correct #6 Phillips screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure alignment, then tighten until snug — do not overtighten
• Replace stripped or damaged screws to ensure secure fastening
• Wear eye protection and disconnect power to the appliance before working on components

A replacement galvanized front bulkhead assembly with light opening that restores the washer's cabinet front and supports the door and control area. Replaces a damaged or corroded front panel to help maintain proper door alignment and cabinet integrity. What it does

• Provides the front cabinet support and mounting surface for the door and related hardware
• Includes the light opening for washer interior/accessory lights or indicators
• Restores proper door seal alignment and front-end rigidity after collision or corrosion damage
• Helps stop water intrusion and reduces vibration caused by a bent or weakened front panel

• One galvanized front bulkhead assembly with light opening

• Panel removal may require disconnecting power and detaching door, trim, and controls
• Disconnect power and shut off water before starting work to avoid shock or injury
• Handle edges carefully — metal panels can have sharp edges; wear gloves and eye protection
• Verify alignment and fastener torque during reassembly; test a short wash cycle to confirm proper operation

This 8-inch orange jumper wire provides a short, insulated connection between terminals in the washer's control or wiring harness, restoring a reliable electrical path for proper operation and diagnostics. What it does

• Bridges two terminals to complete a circuit or bypass a failed trace in the wiring harness.
• Restores power to a component when a broken or damaged wire is the cause.
• Useful for testing or replacing a short segment of harness wiring without replacing the entire loom.
• Can help eliminate intermittent faults caused by corroded or loose terminal connections.

• One 8" orange insulated jumper wire.

• Always disconnect power to the appliance before testing or installing wiring.
• Verify terminal locations and correct polarity before making connections.
• Use proper crimp connectors or solder and heat-shrink to secure joints; avoid exposed conductors.
• Route and secure the jumper away from moving parts, high-heat areas, and pinch points.

This right-side end cap is a replacement trim piece that restores the finished appearance of the washer control/top edge and protects edges from wear. It matches the original shape and color for a clean factory look. What it does:

• Covers and protects the right edge/end of the control/top trim to prevent exposed edges
• Restores appearance when the original cap is cracked, broken or missing
• Helps keep the trim secured and reduces the chance of snagging or catching
• Matches factory color and fit for a seamless replacement

• Disconnect power to the appliance before beginning any repair.
• Remove the affected trim or panel per the service manual to access the end cap.
• The cap typically snaps or slides into place; use a plastic pry tool to avoid damaging surrounding trim.

This is a tapping screw with a hex head and Torx drive designed to fasten panels and components on Speed Queen laundry appliances. It provides a secure, vibration-resistant hold for repeatable service and repairs. What it does

• Fastens outer panels, brackets and internal parts where a self-tapping screw is required
• Holds components tight to prevent rattling or misalignment during operation
• Replaces missing, worn or stripped screws that cause loose or insecure parts
• Used when a screw must tap its own threads in sheet metal or thin substrates

• One tapping screw (hex head Torx)

• Use the correct Torx driver bit to avoid stripping the drive recess
• Drive straight and steady; do not over-torque to prevent thread or sheet-metal damage
• Follow OEM service instructions for panel removal and fastening order
• Disconnect power and follow safety precautions before servicing the appliance

A replacement low-profile Phillips screw used to secure panels and components on compatible laundry equipment. Provides a secure, low-profile fastening where a shorter head is required. What it does:

• Fastens trim, control panels, or small brackets where a low-profile head is needed
• Restores secure attachment when original screws are missing or stripped
• Helps eliminate rattling or loose panels caused by missing hardware
• Matches common #8 AB-18 x 1/2" thread and length for specified OEM fittings

• Use the correct Phillips screwdriver to avoid cam-out and head damage
• Start threading by hand to avoid cross-threading; do not force
• Tighten until snug—do not over-torque to prevent stripping the mating threads
• If threads are damaged, replace with an appropriate fastener or repair the hole before installing