Ade4brgs175tw01 Parts

A replacement wedge for the door handle that restores a secure grip and smooth door operation. Fits the white trim area of the handle assembly to replace cracked, broken, or worn wedges and improve door feel. What it does:

• Replaces a damaged or missing wedge piece that holds the door handle trim in position.
• Restores a stable gripping surface so the door opens and closes without slipping.
• Helps correct symptoms such as a loose, cracked, or partially detached handle wedge.
• Matches the white finish used on the handle trim for a consistent appearance.

• One white wedge door-handle piece as shown

• Disconnect power to the appliance before starting any repair.
• Installation typically requires basic hand tools; remove the handle/trim to access the wedge.
• Align the wedge and snap or fasten into place without forcing; avoid over-tightening fasteners.

This self-tapping screw secures panels and components on Speed Queen laundry appliances, restoring firm fastening and preventing rattles or gaps. Compact 8-18 x 3/8 size for use where a small, hex-washer-head fastener is required. What it does:

• Cuts its own mating thread in sheet metal or plastic mounting holes for a secure fit
• Holds control panels, trim pieces, and light brackets in place
• Replaces missing or damaged fasteners that cause loose or vibrating panels
• Helps restore proper panel alignment and reduces noise from loose parts

• Disconnect power before servicing the appliance
• Use the matching hex-washer driver or nut driver to seat the screw
• Start straight and apply steady pressure; avoid cross-threading
• Do not overtighten — snug until panels are secure

A black rocker switch used to control power or function circuits on compatible Speed Queen appliances. Replaces a worn or broken rocker to restore reliable on/off or selection operation and improve user control. What it does:

• Acts as the user-facing actuator that opens and closes electrical contacts when pressed
• Re-establishes circuit connection for affected control functions (power, cycle selection, etc.)
• Common symptom of failure: switch feels stuck, loose, or does not click/respond
• Also replaced when housing or actuator shows visible damage or excessive wear

• One black rocker switch

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Access may require removing the control panel; handle surrounding trim carefully to avoid damage
• Inspect switch mounting and wiring; replace only with matching part to ensure proper fit and function

This dryer steam nozzle directs steam into the dryer drum to help remove wrinkles and refresh fabrics. It replaces a worn or damaged nozzle to restore proper steam flow and steaming performance. What it does:

• Channels steam from the boiler/steam supply into the drum for wrinkle-release and fabric refreshing
• Helps ensure steam is delivered where intended instead of leaking or dispersing inefficiently
• Supports normal dryer steam functions when installed correctly

• One dryer steam nozzle

• Install only after disconnecting power and shutting off steam/water supply; follow OEM service instructions
• Inspect surrounding fittings, hoses, and gaskets for wear and replace if needed
• Use appropriate tools and torque; avoid overtightening which can crack plastic or damage threads

This is a 8-16 x 5/8 tapping screw with a #6 Phillips drive, used to fasten panels and components on compatible appliances. It provides a secure, low-profile hold for trim, brackets and covers. What it does:

• Secures panels, trim pieces, brackets or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment and fit of exterior or interior panels
• Provides a threaded connection in sheet metal or tapped holes

• Use the correct #6 Phillips screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure alignment, then tighten until snug — do not overtighten
• Replace stripped or damaged screws to ensure secure fastening
• Wear eye protection and disconnect power to the appliance before working on components

A replacement galvanized front bulkhead assembly with light opening that restores the washer's cabinet front and supports the door and control area. Replaces a damaged or corroded front panel to help maintain proper door alignment and cabinet integrity. What it does

• Provides the front cabinet support and mounting surface for the door and related hardware
• Includes the light opening for washer interior/accessory lights or indicators
• Restores proper door seal alignment and front-end rigidity after collision or corrosion damage
• Helps stop water intrusion and reduces vibration caused by a bent or weakened front panel

• One galvanized front bulkhead assembly with light opening

• Panel removal may require disconnecting power and detaching door, trim, and controls
• Disconnect power and shut off water before starting work to avoid shock or injury
• Handle edges carefully — metal panels can have sharp edges; wear gloves and eye protection
• Verify alignment and fastener torque during reassembly; test a short wash cycle to confirm proper operation

This right-side end cap is a replacement trim piece that restores the finished appearance of the washer control/top edge and protects edges from wear. It matches the original shape and color for a clean factory look. What it does:

• Covers and protects the right edge/end of the control/top trim to prevent exposed edges
• Restores appearance when the original cap is cracked, broken or missing
• Helps keep the trim secured and reduces the chance of snagging or catching
• Matches factory color and fit for a seamless replacement

• Disconnect power to the appliance before beginning any repair.
• Remove the affected trim or panel per the service manual to access the end cap.
• The cap typically snaps or slides into place; use a plastic pry tool to avoid damaging surrounding trim.

This is a tapping screw with a hex head and Torx drive designed to fasten panels and components on Speed Queen laundry appliances. It provides a secure, vibration-resistant hold for repeatable service and repairs. What it does

• Fastens outer panels, brackets and internal parts where a self-tapping screw is required
• Holds components tight to prevent rattling or misalignment during operation
• Replaces missing, worn or stripped screws that cause loose or insecure parts
• Used when a screw must tap its own threads in sheet metal or thin substrates

• One tapping screw (hex head Torx)

• Use the correct Torx driver bit to avoid stripping the drive recess
• Drive straight and steady; do not over-torque to prevent thread or sheet-metal damage
• Follow OEM service instructions for panel removal and fastening order
• Disconnect power and follow safety precautions before servicing the appliance

A replacement low-profile Phillips screw used to secure panels and components on compatible laundry equipment. Provides a secure, low-profile fastening where a shorter head is required. What it does:

• Fastens trim, control panels, or small brackets where a low-profile head is needed
• Restores secure attachment when original screws are missing or stripped
• Helps eliminate rattling or loose panels caused by missing hardware
• Matches common #8 AB-18 x 1/2" thread and length for specified OEM fittings

• Use the correct Phillips screwdriver to avoid cam-out and head damage
• Start threading by hand to avoid cross-threading; do not force
• Tighten until snug—do not over-torque to prevent stripping the mating threads
• If threads are damaged, replace with an appropriate fastener or repair the hole before installing