Ade4brgs176tw01 Parts

This idler lever is the replacement lever that supports the washer's drive system, restoring proper belt tension and smooth drum rotation. Replacing a worn lever reduces slipping and helps the washer run quietly and reliably. What it does:

• Positions and tensions the drive belt or pulley to transfer motor power to the drum
• Restores proper belt alignment to prevent slipping or loss of drive
• Removes noise caused by a loose or damaged idler lever during spin or agitation
• Helps prevent uneven or intermittent drum movement linked to a failing lever

• One lever, idler

• Disconnect power before beginning any repair to avoid electric shock
• Inspect adjacent components (belt, pulleys, mounts) and replace if worn for best results
• Use basic hand tools; secure parts per the manufacturer's service instructions

This moisture sensor base is the mounting support for the washer's moisture-sensing assembly, helping the machine detect dampness and manage automatic dry-time. It replaces a damaged or worn sensor mount to restore proper moisture detection. What it does

• Holds the moisture-sensing contacts in the correct position so the control can read drum moisture
• Helps the washer detect wet loads and end cycles appropriately
• Can correct symptoms like inconsistent dryness sensing, premature or delayed cycle termination, or erratic auto-dry behavior
• Works with the existing sensor contacts and wiring harness to transmit moisture signals to the control

• One moisture sensor base (mount)

• Disconnect power to the appliance before starting any repair
• Handle the sensor contacts and wiring gently; avoid bending or contaminating contact surfaces
• Verify correct alignment and secure mounting so the sensor contacts reliably touch the drum or probe area
• Replace damaged sensing contacts or wiring; test the washer through a cycle after installation

This is a replacement black wire assembly used to restore a secure electrical connection between components in your appliance. It replaces damaged or worn wiring to help re-establish reliable power/signal routing. What it does

• Carries power or signal between internal components to enable normal operation
• Replaces frayed, cut or damaged wiring that can cause intermittent operation
• Helps eliminate loose or corroded connections that can result in failure to start or inconsistent performance
• Prevents arcing or shorting when insulation or connectors are compromised

• One black wire assembly as shown

• Disconnect all power to the appliance before beginning work to avoid shock or injury
• Match wire routing and connector orientation to the original; refer to the appliance wiring diagram
• Make sure connectors are fully seated and any strain reliefs or clips are secured away from moving parts and heat sources
• If insulation or connector damage is present elsewhere, inspect and replace affected parts rather than making temporary repairs

This air duct assembly routes airflow inside the washer cabinet to support proper ventilation and cooling of internal components. It replaces damaged or cracked ducts to restore directed airflow and reduce overheating risk. What it does:

• Channels air from the blower/fan to internal areas to help dissipate heat and control moisture.
• Prevents airflow leaks that can cause poor ventilation, unusual heat buildup, or increased drying times.
• Restores proper airflow paths that may stop intermittent fan noise caused by loose or broken ducting.
• Keeps dust and lint contained within the duct path to reduce buildup on sensitive components.

• One light-gray air duct assembly

• Disconnect power to the appliance before attempting any service.
• Remove access panels as needed to reach the duct; handle plastic parts gently to avoid cracking.
• Verify alignment and secure all fasteners; ensure ducts seat properly over blower or vent connections.
• Inspect and replace as needed for best results.

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This bulkhead light assembly replaces the interior service light on commercial laundry machines, restoring illumination for easier loading and maintenance access. It's a direct-fit service kit designed for quick replacement. What it does:

• Replaces a burned-out or flickering bulkhead/service light
• Restores interior visibility for loading, unloading, and troubleshooting
• Replaces a cracked or damaged light housing or lens that lets moisture in
• Helps eliminate unexpected dark or dim compartment lighting

• Disconnect power to the machine before starting any work to avoid shock
• Remove access panels or bulkhead cover per the service manual to reach the light assembly
• Handle the lens and bulb carefully; ensure proper seating and secure fasteners

This front panel replaces a cracked, worn, or damaged control console face to restore the appliance's appearance and protect the control components. It provides a clean mounting surface for the console controls and switches. What it does:

• Covers and protects the control area from spills, dust, and physical damage
• Restores a finished, factory look when the original panel is dented, scratched, or broken
• Helps keep buttons and switches aligned and accessible for normal operation
• Commonly replaced when the panel is cracked, warped, or cosmetically damaged

• Disconnect power to the appliance before starting any work
• Remove the console trim and mounting screws to access and replace the front panel
• Handle panels carefully to avoid scratching or bending during installation
• Reconnect power and verify controls operate correctly after installation

This rear bulkhead assembly provides the rear tub support and a watertight seal to keep washer water contained and flowing correctly. It replaces a damaged or leaking rear housing to stop rear leaks and restore proper tub alignment. What it does:

• Seals the rear of the inner tub to prevent water from leaking at the back of the washer
• Supports and aligns the tub to help maintain smooth spinning and prevent rubbing
• Directs drain and rinse water flow toward the pump and drain path
• Helps reduce water dripping onto the cabinet floor or rear-facing components

• Disconnect power and turn off water supply before beginning any repairs.
• Typical access requires removing the washer top or rear panel; follow the OEM service manual for your model.
• Inspect surrounding gaskets, hoses, and fasteners for wear and replace if needed.
• Ensure the sealing surface and lip are clean and fully engaged during reassembly to prevent leaks.

This access panel assembly covers the washer's service area to protect internal components and give technicians a safe, removable entry point for maintenance. It restores the cabinet's exterior and keeps wiring and parts enclosed. What it does:

• Replaces a missing, dented, or damaged access panel to secure internal components
• Provides a removable service opening for accessing controls, valves, and wiring
• Helps stop debris and lint from reaching internal parts
• Reduces noise and vibration caused by loose or damaged panels
• Restores the appliance's finished appearance and safety

• Disconnect power and water supply before starting any service
• Typical installation requires removal of a few screws; use basic hand tools
• Handle edges carefully; panels can have sharp metal edges

A one-piece rolled exhaust duct that routes dryer exhaust and lint from the appliance to the home vent. Durable sheet-metal construction keeps airflow consistent and helps maintain dryer performance. What it does:

• Channels hot, moist air and lint from the dryer to the external vent
• Prevents exhaust air from leaking into the laundry area
• Helps reduce lint buildup in the cabinet and transition ducting
• Supports proper airflow to improve drying consistency and odor control

• One one-piece rolled exhaust duct

• Disconnect power (and shut off gas supply for gas dryers) before servicing
• Inspect surrounding venting and housing; replace if crushed or heavily corroded
• Secure with the proper clamps or fasteners and maintain an unobstructed, smooth airflow path
• Follow the dryer manufacturer's venting guidelines and local codes

This LED cylinder light assembly restores bright, reliable illumination inside the drum, making loading and unloading easier. Replacing a failed or flickering light module brings back clear visibility and helps prevent small items from being left behind.

• Illuminates the interior drum/cylinder when the door is opened or during designated cycle stages (varies by model)
• Common fix for no interior light, dim light, or intermittent/flickering light
• 120V LED design provides consistent, dependable lighting
• Connects to the factory wiring harness on applicable units

Includes: One LED cylinder light assembly.

• Disconnect power to the appliance before servicing
• Access the light location; the assembly mounts at the drum/cylinder opening
• Reconnect wiring securely and route away from moving parts; reuse existing mounting hardware if required
• Test light operation before fully reassembling panels

This timer conversion kit adapts an older-style washer timer to the RS-style timer configuration so the machine accepts the newer control. It lets you replace an obsolete timer assembly without changing the whole harness or timer module. What it does:

• Provides the mechanical adapter and hardware needed to convert an older timer mounting to the RS-style timer
• Enables proper alignment and secure mounting for the replacement RS-style timer
• Helps restore timer selector function when the original timer mounting or interface is incompatible with RS-style replacements
• Addresses symptoms such as a replacement timer that won't mount correctly, loose or misaligned timer, or selector knob not engaging

• Always unplug the appliance before beginning any repair to avoid electric shock
• Basic hand tools are typically required; follow the OEM instructions for correct orientation and fastener torque

The Output Control Board Assembly is an OEM part for SpeedQueen dryers. It is responsible for controlling various electrical functions during the drying cycle, such as motor operation, temperature monitoring, and timing functions.

Causes of a bad output control board can include component failures due to wear and tear over time, exposure to moisture or excess heat, or shorts in the circuitry from power surges or improper maintenance.

Symptoms of a bad output control board include:

• The dryer not turning on or functioning
• Incorrect or no heat being produced
• Fault codes appearing on the display
• Improper drying times or continuous cycling
• Intermittent operation

The Heater Assembly Wire is an OEM component specifically designed for Speed Queen commercial and industrial washing machines. The heater assembly wire works with electronic controls to rapidly heat water on demand. This allows different cycles to use water temperatures best suited to each load type. Precise heating saves energy and leads to more consistent cleaning and rinsing results.

Symptoms of a bad heater assembly wire include:

• Inability to heat water effectively or reach required temperatures
• Fluctuations in temperature readings and unstable heating
• Error codes related to heating issues displayed  

Causes are typically cracks, corrosion or breaks in the heating element over extended usage. 

A replacement wedge for the door handle that restores a secure grip and smooth door operation. Fits the white trim area of the handle assembly to replace cracked, broken, or worn wedges and improve door feel. What it does:

• Replaces a damaged or missing wedge piece that holds the door handle trim in position.
• Restores a stable gripping surface so the door opens and closes without slipping.
• Helps correct symptoms such as a loose, cracked, or partially detached handle wedge.
• Matches the white finish used on the handle trim for a consistent appearance.

• One white wedge door-handle piece as shown

• Disconnect power to the appliance before starting any repair.
• Installation typically requires basic hand tools; remove the handle/trim to access the wedge.
• Align the wedge and snap or fasten into place without forcing; avoid over-tightening fasteners.