Ade8060 Parts

This galvanized dryer cylinder assembly replaces the drum that holds clothes and directs airflow for efficient tumbling and drying. Designed as a direct-fit replacement to restore drum integrity and proper rotation. What it does:

• Replaces a worn, dented, or corroded dryer drum to prevent fabric damage and restore normal tumbling
• Provides the rotating surface that carries clothes through the dryer's airflow path
• Helps maintain proper drum alignment and reduces rubbing noises from a damaged drum
• Restores an even tumbling action that can improve drying consistency

• Intended for DIYers; refer to your service manual for model-specific instructions
• Disconnect power and gas before beginning service to avoid shock or fire hazards
• Inspect and replace related wear items (drum seals, rollers, glides, or belt) if they show wear during installation
• Handle the drum carefully to avoid sharp edges and to protect the painted/galvanized finish

This heater duct assembly routes heated air from the dryer's heating unit to the drum so your loads dry efficiently and evenly. It replaces a damaged or obstructed duct to restore proper airflow and drying performance. What it does

• Channels hot air from the heating element into the drum for consistent drying.
• Restores airflow if a cracked or broken duct was leaking heat inside the cabinet.
• Helps address symptoms like reduced drying performance or longer cycle times.
• Prevents heat loss that can cause the dryer to run inefficiently.

• Disconnect power (unplug electric or shut off gas and unplug) before beginning any repair.
• High-level access may require removing the dryer's front or top panel; use basic hand tools and follow the dryer's service manual.
• Inspect surrounding seals and fasteners; replace any damaged clips or gaskets for a proper fit.
• Never operate the dryer with the duct disconnected or obstructed; ensure lint is cleared before reassembly.

This door hinge secures and lets the appliance door pivot smoothly, restoring proper alignment and reliable opening/closing. A direct-fit replacement designed to return worn or damaged hinges to correct function. What it does:

• Supports the door and provides a pivot point for opening and closing
• Restores proper door alignment and prevents sagging or uneven gaps
• Helps the door latch and seal correctly by maintaining hinge position
• Common symptom fix: loose, noisy, tilted, or non-closing door

• Disconnect power and water before beginning any repairs
• Support the door during removal/installation to prevent dropping or damage
• Use the factory mounting screws and torque to OEM spec; replace damaged fasteners
• If alignment or latch issues persist after install, check strike and door seal for wear or damage

This rear bulkhead assembly with seal replaces the washer's rear tub enclosure to restore a watertight connection and support the drum. It prevents leaks and helps maintain proper tub alignment for reliable operation. What it does:

• Seals the back of the washer tub to stop water from leaking at the rear
• Provides the mounting surface and alignment for the tub and rear components
• Helps prevent moisture damage to internal components and wiring
• Common symptom: water pooling or dripping from the rear of the machine

• One rear bulkhead assembly with seal

• Disconnect power and shut off water before beginning any repair
• Handle the seal carefully to avoid nicks; damaged seals can leak
• Basic hand tools required; verify fastener locations and torque per OEM guidance

A clear silicone adhesive/sealant used to bond and seal appliance trim and components, helping restore watertight and stable assemblies. Supplies a durable, flexible hold for small repairs where factory adhesive is specified. What it does:

• Bonds trim, panels, and small plastic or metal parts to prevent movement and leaks
• Seals gaps to reduce water intrusion around housings and door areas
• Provides a flexible, durable hold that resists vibration and temperature changes
• Useful for reattaching trim, tabs, and molded parts when original adhesive has failed

• One (1) clear 3 oz tube of DOW 737 adhesive

• Use in a well-ventilated area; wear gloves and eye protection to avoid skin/eye contact
• Surface must be clean, dry, and free of oils or old adhesive for best adhesion
• Apply as a thin, even bead; allow recommended cure time before reassembling or using appliance
• Follow any OEM repair instructions and local disposal guidance for adhesive containers

This front bulkhead assembly replaces the washer's front tub support and splash barrier, restoring proper drum alignment and helping prevent leaks. Built as a service-pack replacement to fit factory mounting points and finishes. What it does:

• Supports and aligns the washer drum and outer tub for smooth spinning
• Forms a splash barrier to help keep water inside the tub and away from controls
• Provides the factory mounting surface for door seal, bearing, and related components
• Helps reduce vibration caused by misaligned or damaged bulkheads

• Disconnect power and water supply before starting any repairs
• Drain the washer and remove the front panel or cabinet to access the bulkhead
• Keep track of gaskets, seals, and fasteners; replace any worn seals to prevent leaks

This idler lever is the replacement lever that supports the washer's drive system, restoring proper belt tension and smooth drum rotation. Replacing a worn lever reduces slipping and helps the washer run quietly and reliably. What it does:

• Positions and tensions the drive belt or pulley to transfer motor power to the drum
• Restores proper belt alignment to prevent slipping or loss of drive
• Removes noise caused by a loose or damaged idler lever during spin or agitation
• Helps prevent uneven or intermittent drum movement linked to a failing lever

• One lever, idler

• Disconnect power before beginning any repair to avoid electric shock
• Inspect adjacent components (belt, pulleys, mounts) and replace if worn for best results
• Use basic hand tools; secure parts per the manufacturer's service instructions

This moisture sensor base is the mounting support for the washer's moisture-sensing assembly, helping the machine detect dampness and manage automatic dry-time. It replaces a damaged or worn sensor mount to restore proper moisture detection. What it does

• Holds the moisture-sensing contacts in the correct position so the control can read drum moisture
• Helps the washer detect wet loads and end cycles appropriately
• Can correct symptoms like inconsistent dryness sensing, premature or delayed cycle termination, or erratic auto-dry behavior
• Works with the existing sensor contacts and wiring harness to transmit moisture signals to the control

• One moisture sensor base (mount)

• Disconnect power to the appliance before starting any repair
• Handle the sensor contacts and wiring gently; avoid bending or contaminating contact surfaces
• Verify correct alignment and secure mounting so the sensor contacts reliably touch the drum or probe area
• Replace damaged sensing contacts or wiring; test the washer through a cycle after installation

This is a replacement black wire assembly used to restore a secure electrical connection between components in your appliance. It replaces damaged or worn wiring to help re-establish reliable power/signal routing. What it does

• Carries power or signal between internal components to enable normal operation
• Replaces frayed, cut or damaged wiring that can cause intermittent operation
• Helps eliminate loose or corroded connections that can result in failure to start or inconsistent performance
• Prevents arcing or shorting when insulation or connectors are compromised

• One black wire assembly as shown

• Disconnect all power to the appliance before beginning work to avoid shock or injury
• Match wire routing and connector orientation to the original; refer to the appliance wiring diagram
• Make sure connectors are fully seated and any strain reliefs or clips are secured away from moving parts and heat sources
• If insulation or connector damage is present elsewhere, inspect and replace affected parts rather than making temporary repairs

This air duct assembly routes airflow inside the washer cabinet to support proper ventilation and cooling of internal components. It replaces damaged or cracked ducts to restore directed airflow and reduce overheating risk. What it does:

• Channels air from the blower/fan to internal areas to help dissipate heat and control moisture.
• Prevents airflow leaks that can cause poor ventilation, unusual heat buildup, or increased drying times.
• Restores proper airflow paths that may stop intermittent fan noise caused by loose or broken ducting.
• Keeps dust and lint contained within the duct path to reduce buildup on sensitive components.

• One light-gray air duct assembly

• Disconnect power to the appliance before attempting any service.
• Remove access panels as needed to reach the duct; handle plastic parts gently to avoid cracking.
• Verify alignment and secure all fasteners; ensure ducts seat properly over blower or vent connections.
• Inspect and replace as needed for best results.

This switch retainer clip secures a small appliance switch in place so the switch stays aligned and operates correctly. It helps maintain reliable switch contact for normal door or control functions. What it does:

• Holds the door/control switch securely to prevent movement or misalignment
• Helps ensure consistent on/off contact for the related switch
• Can prevent intermittent operation or failure caused by a loose switch
• Small plastic/metal retainer designed for exact OEM fit in the switch assembly

• Disconnect power to the appliance before servicing to avoid electric shock
• Typically installs by snapping or sliding onto the switch or bracket; no special tools usually required
• Inspect surrounding switch and wiring for damage; replace if wiring or switch is compromised

This 1/4-20 nut secures related fasteners in appliance assemblies to keep components aligned and stable. It's a direct-fit replacement when the original nut is worn, stripped, or missing. What it does:

• Threads onto a 1/4-20 bolt or stud to lock parts together
• Restores tight mechanical connections that reduce vibration and noise
• Helps maintain proper alignment of panels, brackets, or linkage
• Commonly replaced when the original nut is rounded, corroded, or loose

• One 1/4-20 nut

• Use the correct 1/4-20 bolt or stud size and thread engagement
• Tighten to manufacturer torque if specified; avoid over-tightening
• Inspect adjoining parts (bolt, washer, bracket) for wear before reassembly
• Turn off and unplug the appliance before performing repairs

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten