Ade8060 Parts

Dryer won't start or respond to controls? This electronic control board manages cycle timing and user settings. Restores normal operation when failed.

10-24 threaded machine screw secures panels, brackets, and internal assemblies in appliances. Replace missing, stripped, or damaged screws.

Self-tapping hex washer head screw secures plastic trim and sheet-metal panels on dryers. Replace worn, stripped, or missing screws during repairs.

Seals the back of the dryer drum to prevent air leaks and maintain proper alignment. Replace if you notice poor drying or air escaping. Confirm fit with your model.

Replace your dryer door seal to prevent heat loss, contain lint, and restore efficient drying. Fits multiple models. Confirm compatibility before ordering.

Converting your gas dryer from natural gas to liquid propane? This LP conversion kit modifies the fuel orifice and components. Typical install: 1 hour.

A replacement cord lead-in that routes incoming power into the appliance and provides a secure connection point for the main wiring. Restores reliable electrical feed and helps eliminate intermittent power or no-power issues. What it does:

• Transfers household power from the external cord to the appliance's internal wiring
• Provides a stable inlet connection and strain relief for the incoming power cable
• Commonly replaced for symptoms such as no power, intermittent power, blown fuses, or visible damage/corrosion at the inlet
• Matches OEM fit and mounting for a direct replacement when the part number is correct

• One cord lead-in assembly

• Disconnect all power at the breaker or unplug the appliance before starting work
• Route wires and secure strain relief per OEM guidance; tighten terminal connections firmly but do not overtighten
• If wiring or terminal damage is present, replace or repair per local electrical code

Replace a stripped or broken motor pulley that prevents your dryer drum from turning. Direct-fit part restores belt engagement and motor rotation.

This washer cylinder baffle mounts to the inner basket and lifts garments as the basket turns. Replacing a cracked, loose, or missing baffle restores proper turnover, reduces banging noises, and helps prevent fabric snags.

• Lifts and tumbles clothes for effective wash action
• Helps distribute the load to minimize imbalance and noise
• Guides garment movement for consistent wash action
• Common failure symptoms: loose or missing baffle, rattling/banging sounds, clothes catching or excessive wear

• Disconnect power and shut off water before servicing; wear cut-resistant gloves
• Open the door and rotate the basket to access the baffle fasteners; support the baffle while removing screws
• Align the new baffle with the keyed slots/holes and tighten the screws securely
• Manually rotate the basket to confirm clearance, then run a short test cycle to verify smooth operation

Secures internal components inside your dryer cabinet. Replace if bent, cracked, stripped, or missing to restore proper alignment and stability.

This wiring harness connects a homestyle 240V laundry appliance's power and internal wiring, providing a reliable plug-and-play link between the power source and the machine's components. It replaces damaged or worn harnesses to restore safe electrical connections. What it does:

• Routes 240V power to the appliance's internal circuits and controls
• Replaces frayed, burned, or broken wiring that can cause power loss or intermittent operation
• Prevents loose or corroded connections that can lead to arcing or component failure
• Useful when the appliance has no power, trips breakers, or shows electrical faults related to wiring

• One homestyle 240V wiring harness

• Disconnect all power at the breaker before inspecting or replacing the harness — 240V is lethal
• Compare connectors and wire colors to the original harness; swap only when you confirm a match
• Secure harness routing away from moving parts and heat sources to avoid chafing

This front bulkhead assembly replaces the washer's front tub support and splash barrier, restoring proper drum alignment and helping prevent leaks. Built as a service-pack replacement to fit factory mounting points and finishes. What it does:

• Supports and aligns the washer drum and outer tub for smooth spinning
• Forms a splash barrier to help keep water inside the tub and away from controls
• Provides the factory mounting surface for door seal, bearing, and related components
• Helps reduce vibration caused by misaligned or damaged bulkheads

• Disconnect power and water supply before starting any repairs
• Drain the washer and remove the front panel or cabinet to access the bulkhead
• Keep track of gaskets, seals, and fasteners; replace any worn seals to prevent leaks

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

This wave washer is a spring-style spacer used in washer assemblies to apply tension and maintain proper spacing. It controls endplay so parts fit securely and the machine runs smoothly with reduced vibration and noise during wash and spin cycles.

• Provides spring preload to maintain correct spacing in rotating assemblies
• Helps limit endplay that can cause rattling, chatter, or intermittent engagement
• Can help address symptoms like metallic noises, excessive play/wobble, or rough operation during agitation or spin
• Replace if the original washer is flattened, cracked, or missing

• Disconnect power and turn off water before servicing
• Note the exact stack order and orientation of spacers/shims during disassembly
• Install the new wave washer in the same orientation; do not bend or deform it
• Reassemble and hand-rotate components to check for smooth operation before test-running

Washer adhesive is a clear sealant used to secure various internal components and create watertight seals within the washing machine. Use this adhesive when experiencing water leaks, loose parts, or when replacing gaskets and seals during repairs.