Adg4475tq1 Parts

This valve bracket and pipe assembly secures and routes the washer's inlet valve plumbing, helping restore proper water flow to the tub. Use when the inlet valve mounting or water feed pipe is damaged, loose, or leaking. What it does:

• Holds the water inlet valve in the correct position and secures plumbing connections
• Routes water from the valve to the tub via the attached pipe
• Helps stop leaks and prevents valve movement that can interrupt water fill
• Commonly replaced when brackets are cracked, pipes are bent, or fittings leak

• Turn off electrical power and shut off the water supply before starting any repair
• Use appropriate tools and avoid overtightening plastic fittings to prevent damage

This dryer steam nozzle directs steam into the dryer drum to help remove wrinkles and refresh fabrics. It replaces a worn or damaged nozzle to restore proper steam flow and steaming performance. What it does:

• Channels steam from the boiler/steam supply into the drum for wrinkle-release and fabric refreshing
• Helps ensure steam is delivered where intended instead of leaking or dispersing inefficiently
• Supports normal dryer steam functions when installed correctly

• One dryer steam nozzle

• Install only after disconnecting power and shutting off steam/water supply; follow OEM service instructions
• Inspect surrounding fittings, hoses, and gaskets for wear and replace if needed
• Use appropriate tools and torque; avoid overtightening which can crack plastic or damage threads

This is a 8-16 x 5/8 tapping screw with a #6 Phillips drive, used to fasten panels and components on compatible appliances. It provides a secure, low-profile hold for trim, brackets and covers. What it does:

• Secures panels, trim pieces, brackets or small components to the appliance frame
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment and fit of exterior or interior panels
• Provides a threaded connection in sheet metal or tapped holes

• Use the correct #6 Phillips screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure alignment, then tighten until snug — do not overtighten
• Replace stripped or damaged screws to ensure secure fastening
• Wear eye protection and disconnect power to the appliance before working on components

This packaged burner assembly supplies and directs the gas flame needed to heat a gas dryer's drum. Replacing a faulty burner assembly restores reliable ignition and helps the dryer produce consistent, usable heat. What it does:

• Houses the burner tube and pilot/orifice components that create and channel the gas flame
• Ignites and sustains the flame used to heat air flowing through the dryer
• Commonly replaced when the dryer won't heat, the burner won't ignite, or flame is weak/intermittent
• Works with the dryer's safety and control systems to shut off gas if ignition fails

• Turn off and disconnect both the electrical supply and the gas supply before beginning work
• Inspect and replace any gaskets or seals as needed; confirm all gas fittings are tight
• After installation, check for gas leaks and proper ignition; follow local codes and safety practices

A replacement galvanized front bulkhead assembly with light opening that restores the washer's cabinet front and supports the door and control area. Replaces a damaged or corroded front panel to help maintain proper door alignment and cabinet integrity. What it does

• Provides the front cabinet support and mounting surface for the door and related hardware
• Includes the light opening for washer interior/accessory lights or indicators
• Restores proper door seal alignment and front-end rigidity after collision or corrosion damage
• Helps stop water intrusion and reduces vibration caused by a bent or weakened front panel

• One galvanized front bulkhead assembly with light opening

• Panel removal may require disconnecting power and detaching door, trim, and controls
• Disconnect power and shut off water before starting work to avoid shock or injury
• Handle edges carefully — metal panels can have sharp edges; wear gloves and eye protection
• Verify alignment and fastener torque during reassembly; test a short wash cycle to confirm proper operation

This front bulkhead assembly replaces the dryer or washer front panel that supports the drum and front bearings, restoring proper drum alignment and enclosure. It helps reduce vibration, air leaks, and rubbing that can cause noise or wear. What it does:

• Supports the drum and front bearing to keep the drum centered during operation
• Provides the mounting surface for the door and front seal to maintain proper airflow and closure
• Prevents drum-to-frame contact that can cause squeaks, scraping, or excess vibration
• Helps keep lint and moisture contained in the drum area to protect internal components

• Disconnect power (and water, if applicable) before starting any repair
• Remove the dryer/washer door and front cover to access mounting fasteners; keep hardware for reassembly
• Transfer any door latch, seal, or trim pieces to the new bulkhead as needed
• After installation, recheck drum rotation and clearances; run a short test cycle to confirm quiet operation

This right-side end cap is a replacement trim piece that restores the finished appearance of the washer control/top edge and protects edges from wear. It matches the original shape and color for a clean factory look. What it does:

• Covers and protects the right edge/end of the control/top trim to prevent exposed edges
• Restores appearance when the original cap is cracked, broken or missing
• Helps keep the trim secured and reduces the chance of snagging or catching
• Matches factory color and fit for a seamless replacement

• Disconnect power to the appliance before beginning any repair.
• Remove the affected trim or panel per the service manual to access the end cap.
• The cap typically snaps or slides into place; use a plastic pry tool to avoid damaging surrounding trim.

This is a tapping screw with a hex head and Torx drive designed to fasten panels and components on Speed Queen laundry appliances. It provides a secure, vibration-resistant hold for repeatable service and repairs. What it does

• Fastens outer panels, brackets and internal parts where a self-tapping screw is required
• Holds components tight to prevent rattling or misalignment during operation
• Replaces missing, worn or stripped screws that cause loose or insecure parts
• Used when a screw must tap its own threads in sheet metal or thin substrates

• One tapping screw (hex head Torx)

• Use the correct Torx driver bit to avoid stripping the drive recess
• Drive straight and steady; do not over-torque to prevent thread or sheet-metal damage
• Follow OEM service instructions for panel removal and fastening order
• Disconnect power and follow safety precautions before servicing the appliance