Ats9169as Parts

This commercial dispenser valve kit replaces the valve assembly that controls measured delivery of detergent or chemical in commercial laundry equipment, restoring reliable dispense and preventing leaks or no-flow issues. What it does

• Controls timed release of detergent/chemical from the dispenser into the washer
• Opens and closes to meter fluid flow when a dispense cycle runs
• Helps stop leaks or drips when functioning correctly
• Commonly replaced for no dispense, intermittent flow, or visible leaking

• One commercial dispenser valve kit (valve assembly)

• Disconnect power and shut off chemical/detergent supply before starting
• Inspect and replace any worn seals or fittings when assembling the new valve
• Tighten connections to manufacturer torque specs and check for leaks after installation
• Run a test dispense cycle to verify correct operation

This water mixing valve assembly controls and blends hot and cold water during washer fill cycles to help achieve the selected wash temperature. Designed as a direct replacement valve for affected Speed Queen top-load and commercial washers. What it does

• Directs and mixes incoming hot and cold water to regulate fill temperature.
• Helps the washer reach and maintain the selected wash temperature for proper cleaning.
• Common symptom: washer fills with only hot or only cold water or delivers inconsistent water temperature.
• Can cause extended fill times or temperature-related cycle issues when failing.

• Disconnect power and shut off water supply before beginning replacement.
• Turn off and drain inlet hoses to avoid water spills; have towels or a bucket ready.
• Basic hand tools required; follow OEM service manual for proper disassembly and reassembly.
• Inspect inlet hoses and seals; check for leaks and test a full cycle after installation.

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.

This timer knob assembly is the replacement control knob that lets you set and adjust cycle time on the dryer/washing machine control. It restores a secure grip and clear cycle selection so you can operate the machine easily. What it does:

• Provides a firm, easy-to-turn control for selecting timer settings and cycles
• Replaces cracked, stripped, or missing knobs that are hard to turn or won't stay set
• Helps ensure the timer/control shaft is engaged for accurate cycle selection
• Matches OEM fit and function for a direct replacement when the knob is worn or damaged

• Disconnect power to the appliance before attempting replacement
• Knob typically pulls straight off the control shaft; align splines and press on until seated
• If a retaining clip or screw is present, remove and reinstall as needed—retain hardware
• Do not force the knob; confirm proper alignment to avoid damaging the control shaft

A non-metal shim used to stabilize and level your appliance for quieter, more reliable operation. Simple, low-profile support that helps correct minor height and balance issues so doors and drawers align and appliances sit securely. What it does:

• Adds thin, non-metallic spacing under feet or frame to correct slight height differences
• Helps stop rocking or tipping that can cause noise, vibration, or misaligned doors
• Supports even weight distribution to reduce uneven wear on adjustable legs
• Useful when adjusting leveling feet can't fully correct a gap or tilt

• Place shim under the appliance foot or frame where additional height or support is needed
• Re-check appliance level and stability after installing; add/remove shims as required
• Use with care to avoid creating instability; pair with proper leveling adjustments

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

This replacement ice cube tray is a direct-fit plastic tray designed to hold and release ice cubes in compatible top- or bottom-freezer refrigerators. Restores convenient ice storage and simple manual ice removal. What it does:

• Holds water in separate cavities so ice cubes form evenly.
• Flexes slightly for easier ice release to reduce twisting or chipping.
• Replaces cracked, warped, or missing trays that cause leaking or uneven freezing.
• Helps prevent contamination from freezer debris when used as intended.

• Remove old tray and wipe area clean before installing the new tray.
• Fill tray with water on a level surface and place flat in the freezer to freeze.
• Handle carefully when removing ice to avoid spills; do not force with sharp tools.
• Clean tray before first use and as needed; follow refrigerator manufacturer's care guidance.

This Drive belt keeps the washer's transmission and tub turning by transferring motor power to the drum. Replaces a worn or broken belt to restore normal agitation and spinning performance. What it does:

• Transfers motor torque to the transmission/drum so the washer agitates and spins
• Stops slippage that can cause slow or no spin/agitate cycles
• Helps eliminate squealing or burning-rubber noises when the belt is worn
• Prevents further motor/drive damage from a broken or glazed belt

• Disconnect power and water supply before starting any repairs
• Remove access panels and shift the drum to relieve belt tension for removal
• Inspect pulleys, idler, and motor shaft for wear or debris before installing the new belt
• Route the belt according to the OEM diagram, then test run the machine

This small sealing washer fits the washer's water pressure assembly to help maintain a proper watertight seal at the pressure/valve connection. Replacing a worn washer reduces leaks and helps the fill/pressure system operate as intended. What it does

• Provides a watertight seal at the water pressure/valve connection to prevent leaks.
• Helps maintain correct pressure feedback to the washer's water control system.
• Wear or damage can allow leaking at the valve or inconsistent fill behavior.
• Simple, low-cost part commonly replaced when troubleshooting valve leaks.

• Turn off household water supply and unplug the washer before replacing.
• Remove the valve/pressure fitting carefully and replace the old washer with the new one, making sure it seats flat and undamaged.
• Inspect mating surfaces for debris or damage; clean before reassembly.
• If leaks or fill issues persist after replacement, inspect related seals, fittings, and the pressure switch/valve assembly.

This genuine OEM replacement part is a washer control board for commercial Speed Queen Washers. The control board is the main computer of a washer and controls the washing machine's essential functions. If the washer is no longer turning on, spinning, rinsing, or draining properly, it could mean that it needs to be replaced. Luckily replacing a control board is generally an easy repair.Start by unplugging the washer and pulling it out from the wall. Remove the upper back panel to gain access to the control board. Release the locking tabs that hold the control board in place and remove the wire harness along with any individual wires attached to the old board. Make sure to take note of the orientation of the wires by taking a picture with a phone camera. Reconnect the wire harness and individual wires into their correct terminals on the new board and snap it back in place. reinstall the upper back panel and put the washer back in place.This replacement part is sold individually and is compatible with Speed Queen Commercial washing machines.

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

A specialized service wrench designed for Horizon/TL-L style Speed Queen machines to aid technicians during maintenance. Provides a secure grip for installing and removing the specific service fasteners used on these transmissions and hubs. What it does:

• Fits the Horizon/TL-L service fastener to allow controlled tightening or loosening
• Speeds routine service tasks that require the OEM service wrench
• Reduces risk of damaging the fastener when compared with improvised tools
• Useful for maintenance and repair work performed on transmission/hub assemblies

• One Horizon/TL-L service wrench

• Intended for qualified service technicians familiar with Speed Queen equipment
• Disconnect power and follow all safety procedures before servicing
• Use the tool only for its intended fastener; do not use as a pry bar or hammer
• Inspect the tool before use; replace if damaged

This replacement door boot is the flexible rubber seal that fits between the washer door and tub, keeping the wash chamber watertight and helping the door close snugly. Restores a proper seal and reduces leaks and odors. What it does

• Seals the door-to-tub gap to prevent water from escaping during wash cycles.
• Maintains a tight fit so the door closes evenly and the latch engages correctly.
• Helps reduce trapped moisture that can cause mildew, odors, or visible residue.
• Worn, torn, or distorted boots may cause visible leaks, puddling, or poor door closure.

• Disconnect power and water supply before starting any repair.
• Remove the outer door trim and/or retaining clamp carefully to avoid damaging the new boot.
• Inspect and clean the door frame and tub lip before installing the new boot to ensure a proper seal.
• After installation, run a short rinse cycle to check for leaks and correct seating.

A single replacement screw used to fasten appliance panels and components, restoring secure fit and reducing vibration or noise. Simple, low-cost part for repairs that need a missing or stripped fastener. What it does:

• Secures panels, trim, or small component housings to the appliance frame
• Helps stop rattling, vibration, and misalignment caused by loose or missing screws
• Keeps internal components properly seated to maintain normal operation
• Used wherever the OEM specifies this exact fastener

• One replacement screw

• Disconnect power before servicing the appliance to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand first, then tighten snugly—do not overtighten
• Keep small parts away from children and pets