Awn432 Parts

This upper and lower bearing set supports the rotating shaft assembly, helping it turn smoothly and quietly. Replacing worn bearings reduces noise and vibration and protects adjacent components from accelerated wear. What it does:

• Provides radial support so the shaft/drum rotates freely with minimal friction
• Worn bearings can cause rumbling, squealing, or grinding during operation
• Can show play at the shaft or metallic dust near the bearing area

What's included:

• 1 bearing

Install notes:

• Disconnect power and shut off water/gas before servicing
• Access the bearing housing; use a press or proper driver to remove/install bearings—do not strike the races
• Note bearing orientation and seating depth; install squarely and fully
• Inspect the shaft and any related seals/housings and replace if worn or damaged

This idler pulley wheel keeps the drive belt aligned and under constant tension so the drive system runs smoothly and quietly. Replacing a worn wheel helps eliminate belt squeal and prevents premature belt wear or slippage.

• Maintains proper belt tension on the idler arm and guides the belt during operation
• Provides low-friction rotation for smooth belt tracking
• Common symptoms of a worn wheel: squealing/squeaking, frayed or glazed belt, belt slipping off, or intermittent/no drive
• Helps restore reliable belt traction and reduce noise

• Disconnect power and wear work gloves before servicing
• Access the drive system and note the belt routing for reassembly
• Release belt tension, remove retaining hardware, swap the wheel on the idler arm, and re-tension the belt
• Spin the new wheel by hand to inspect belt and idler arm/spring and replace if worn

This timer knob assembly replaces a worn or broken control knob so you can confidently select and adjust cycles. A fresh knob restores a positive grip on the timer shaft and smooth, accurate operation.

• Mounts on the timer shaft to turn and set cycle selection and time
• Restores secure engagement when the original knob is cracked, stripped, loose, or missing
• Helps ensure the timer turns when you rotate the knob
• Common symptoms: knob spins without engaging, difficult to set cycles, visible damage

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft; avoid prying that could damage the control
• Align the new knob with the shaft (flat/D-shape) and press until fully seated
• If the original used a small insert or spring clip, transfer it to the new knob if needed

Replacement timer that controls the washer's cycle sequencing and timing, restoring reliable wash/rinse/spin transitions on compatible commercial/top-load machines. Installs at the control panel to regain proper automatic cycle progression. What it does:

• Advances the washer through timed wash, rinse and spin steps for 4-cycle machines.
• Routes power to motors, valves and switches at the correct points in each cycle.
• Common symptoms: machine won't advance through cycles, stops mid-cycle, or exhibits inconsistent timing.
• Electromechanical control designed for direct swap with matching timer assemblies.

• Always disconnect power at the breaker before servicing the washer.
• Photograph wiring and connector locations before removal to ensure correct reassembly.
• Handle the control shaft and wiring harness carefully to avoid bending cams or damaging terminals.
• Restore power and test cycles after installation.

The Timer is an OEM component specifically designed for Speed Queen commercial washers. It plays a crucial role in controlling wash cycle times and sequences. 

The timer allows for precise regulation of cycle segments to ensure laundered items receive optimal cleaning. It advances operations through the wash, rinse, and spin periods.

Causes of a bad timer can include issues with the electronic circuit board, worn contacts and connections, or faulty input and output switches.

Symptoms of a bad timer include:

• Abnormal cycle lengths that under or over-clean clothes
• The washer fails to advance to subsequent cycles  
• Unexpected stopping or pausing during operation

This OEM Speed Queen replacement part is also compatible with Dexter, Huebsch, Milnor, and IPSO commercial washer models.
 

This washer agitator is the flex-vane style used in select top-load models. It drives the wash action by rolling clothes through water and detergent. Replacing a worn or cracked agitator restores proper turnover and reduces slippage or noise.

• Transfers drive motion to move water and fabrics during the wash cycle
• Flexible vanes promote load turnover for consistent, thorough cleaning
• Common symptoms of failure: no or weak agitation, clothes not circulating, visible cracks or broken fins, unusual noise, or a loose/wobbly agitator
• Designed to replace the original flex-vane agitator on compatible units

• Unplug the washer and turn off water supply before servicing
• Remove the fabric softener dispenser and agitator cap; remove the center bolt, then lift the old agitator off the splined shaft
• Align the new agitator on the drive hub; reuse the original bolt and cap, and tighten securely
• Run a short test cycle to ensure smooth agitation

The Aluminum Pulley Kit is an OEM component specifically designed for Speed Queen commercial washers. This kit includes both an aluminum pulley and the necessary shaft and hardware for proper installation. 

The pulley works with the washer's transmission system to transfer rotational power to the internal drum and cabinet components. It allows for controlled, consistent movements throughout wash and spin cycles.

Symptoms of a bad pulley kit include: 

• Excessive vibration and noise during operation
• The washer fails to advance through cycles properly  
• Damage to belts or other transmission parts

Causes of pulley failure can be wear over time, cracks or warping of the aluminum from overheating, or damage from dropped loads that impact the pulley area.

This OEM Speed Queen replacement part is also compatible with Dexter, Huebsch, Milnor, and IPSO commercial washer models.
 

This white timer knob replaces a cracked or missing knob so you can reliably set your laundry cycles again. It mounts on the timer shaft to restore a secure, easy-to-grip control for selecting cycles.

• Engages the timer shaft so you can set and adjust cycle time/settings
• Restores positive feel and control when turning the timer
• Common symptoms: cracked or stripped knob; spins without moving the timer
• Additional signs: loose or missing knob; hard to turn; falls off

• Disconnect power before service
• Pull the old knob straight off the timer shaft; transfer any retaining clip/insert from the old knob if present
• Align the new knob with the shaft and press until fully seated
• The knob turns the timer smoothly

This left-stop lid hinge is used on top-load washers to support and pivot the lid on the left side while limiting its opening travel. Replacing a bent or worn hinge restores smooth lid movement and proper alignment. What it does:

• Supports and pivots the washer lid on the left side
• Limits lid opening to the designed stop position to prevent overextension
• Helps maintain proper lid alignment with the cabinet
• Typical failure signs: loose or wobbly lid, scraping/binding, uneven closure, or inconsistent lid-switch engagement due to misalignment

• Includes: 1 left-stop lid hinge

• Disconnect power and support the lid to prevent it from dropping
• Remove the left hinge mounting screws from the lid and top panel; lift the lid slightly to free the hinge
• Position the new hinge, start screws by hand, then tighten without overtightening
• Verify even gaps and that the lid opens to the stop and closes smoothly, engaging the lid switch

This timer skirt is the bezel that sits behind the timer knob on the control panel. It replaces a cracked or missing ring so you can securely turn the knob and select settings.

• Sits around the timer shaft as the cosmetic/structural ring behind the knob
• Supports and stabilizes the timer knob during setting selection
• Replaces a cracked, warped, or missing bezel that causes a loose or wobbly knob
• Typical symptoms include a broken ring, misaligned knob, or difficulty selecting settings

• Disconnect power before servicing
• Pull off the timer knob; remove any retaining clip or nut if present
• Remove the old skirt; align and seat the new skirt in the control panel
• Reinstall the knob and verify smooth operation

This right-side lid hinge supports and pivots the washer lid so it opens and closes smoothly. Replacing a worn hinge restores proper lid alignment and helps ensure reliable lid operation.

• Supports the lid and provides the pivot point on the right side
• Worn or bent hinges can cause a misaligned, loose, or squeaky lid
• May help if the lid binds, won't stay aligned, or sags on one side
• Common wear item from repeated opening/closing

• Unplug the appliance before service; use proper PPE
• Support the lid to prevent strain on the remaining hinge
• Transfer and reuse existing mounting screws/hardware unless damaged
• Verify right-hand orientation matches your original part before fastening

This fabric softener dispenser assembly holds liquid softener and releases it during the rinse cycle. Replacing a cracked, missing, or clogged dispenser restores reliable dispensing, reduces messes, and helps keep the washer tub and laundry free of residue. What it does:

• Holds fabric softener and meters its release during the rinse phase
• Uses a simple siphon action to deliver softener evenly into the tub
• Helps prevent spills, streaks, and build-up from manual pouring
• Common symptoms: softener left in cup after cycle, leaks or drips, cracked/loose cup or cap, residue/odor in dispenser area

• 1 fabric softener dispenser assembly

• Disconnect power to the washer before servicing
• Remove the old dispenser from its mounting point; some models require a twist or releasing locking tabs
• Clean any residue from the mounting area to ensure proper flow
• Align and press the new dispenser firmly until fully seated, then test with a small amount of water

This washtub gasket seals the joint between the wash tub and the tub cover, keeping water and suds inside the washer during agitation and spin. Replacing a worn gasket helps stop rim leaks and protects surrounding components.

• Creates a watertight seal between the washtub and tub cover/ring
• Helps prevent water splashing or leaking from the top of the tub
• Common symptoms of failure: water on the floor near the cabinet, moisture around the lid area, visible cracks/flattening of the old gasket
• Restores proper containment of wash water during high-action cycles

• Disconnect power and turn off water before servicing
• Remove top/console and tub cover as directed for your model
• Clean mating surfaces; seat the new gasket evenly without twisting or stretching
• Reinstall the tub cover and fasteners evenly; run a test fill/agitate to check for leaks

Use this drain extension kit to extend your washer's drain hose so it reaches the standpipe or laundry sink. It provides a secure, routed connection that supports proper draining and helps prevent leaks from overstretched or improvised hookups.

• Extends the existing drain hose length for installations where the standpipe or laundry tub is farther away
• Supports correct hose routing and drain height to help prevent kinks and siphoning
• Provides a more secure connection versus improvised extensions or overstretched hoses
• Common symptoms: hose won't reach the drain, drips at the drain connection, or water on the floor near the drain line

• Unplug the washer and turn off water; have towels or a shallow pan ready for residual water
• Attach the extension per manufacturer instructions; route the hose without kinks or sharp bends
• Maintain the standpipe height and air gap specified in your user manual; do not seal the hose into the drain opening
• Secure all connections and run a quick fill/drain test while checking every joint for leaks

This appliance screw replaces a missing or damaged fastener to secure panels and brackets. With a 10B-16 thread and 0.34-inch length, it restores a tight fit to help reduce vibration, rattles, and loosening.

• Fastens sheet-metal parts, brackets, and covers in the appliance cabinet
• Helps maintain alignment and support of components subject to vibration
• Direct replacement for stripped, rusted, or missing hardware
• Can help resolve symptoms like loose panels, rattling noises, or gaps

• Disconnect power; shut off gas/water as applicable before servicing
• Start threads by hand in the original hole or clip to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping
• If the receiving clip/nut is damaged, repair or replace it for a secure hold

A 10 oz cartridge of OEM-specified sealant used to reseal washer assemblies. It forms a flexible, watertight bead to help stop leaks and restore proper sealing around tubs, boots and related joints. What it does:

• Seals gaps and joints around tubs, door boots and panel seams to reduce water leaks
• Bonds to typical appliance surfaces (metal, rubber, many plastics) for a durable seal
• Helps prevent moisture intrusion that can lead to corrosion or interior water damage
• Supplied to OEM specification for correct form and performance in appliance repairs

• Remove old sealant and thoroughly clean and dry surfaces before applying
• Cut nozzle to size and apply an even bead; smooth with a tool or gloved finger for best contact
• Use gloves and eye protection; work in a well-ventilated area and follow label safety directions
• Allow the sealant to fully cure per the manufacturer's instructions before returning the appliance to service