Awn63rsn115tw01 Parts

Flexible water inlet hose that connects the washer's water valve to the machine inlet fitting, restoring proper water flow and helping prevent leaks or drips at the valve connection for reliable fills and operation. What it does:

• Routes water from the valve to the washer inlet; replaces worn, cracked or collapsed hose assemblies.
• Stops leaks and drips at the valve connection that can lead to puddling under the machine.
• Use when the washer has reduced or no water fill, visible hose damage, or steady dripping from the valve area.
• Matches OEM part naming/fit for direct replacement when the original hose is the failed component.

• One replacement hose.

• Disconnect power and shut off the water supply before starting any work.
• Place a towel or pan under the area, relieve water pressure, then remove clamps and the old hose.
• Inspect and replace clamps and any O-rings as needed; route the new hose without kinks and secure clamps snugly.
• After installation, restore water and power, run a short fill cycle and check all connections for leaks.

The Drain Hose is an OEM part for Speedqueen washers. It is responsible for channeling water from the washing machine through the building drain system after each cycle. As a continuously flexing component, the drain hose endures pressure with every load.

Causes of a bad drain hose can include cracking, kinking or splitting resulting from thousands of flex cycles over time. Improper installation may create tight bends that fatigue the material.

Symptoms of a bad Drain Hose include:

• Leaks or drips at hose connections during or after drains
• Limitations in drain rate due to partial blockages or restrictions
• Standing water remaining in washer if hose is compromised
• Potential flooding issues from disconnected or burst hoses

This replacement switch assembly restores the appliance's electrical switching function so the control or safety circuit can open and close when activated. Use it to replace a worn or failed switch and regain expected control response. What it does:

• Acts as the electrical contact that opens or closes a circuit when toggled or pressed
• Commonly used where a user action or door/lid position must be sensed by the control
• Can address symptoms such as no start, unresponsive controls, or intermittent operation tied to the switch circuit
• Transfers the mechanical action to the appliance's control or safety system

What's included: One switch assembly Install notes:

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Verify correct wiring and connector orientation before reassembly; take photos if needed
• Test switch continuity (with power off) after installation to confirm correct operation

A 10 oz cartridge of OEM-specified sealant used to reseal washer assemblies. It forms a flexible, watertight bead to help stop leaks and restore proper sealing around tubs, boots and related joints. What it does:

• Seals gaps and joints around tubs, door boots and panel seams to reduce water leaks
• Bonds to typical appliance surfaces (metal, rubber, many plastics) for a durable seal
• Helps prevent moisture intrusion that can lead to corrosion or interior water damage
• Supplied to OEM specification for correct form and performance in appliance repairs

• Remove old sealant and thoroughly clean and dry surfaces before applying
• Cut nozzle to size and apply an even bead; smooth with a tool or gloved finger for best contact
• Use gloves and eye protection; work in a well-ventilated area and follow label safety directions
• Allow the sealant to fully cure per the manufacturer's instructions before returning the appliance to service

This inlet deflector directs incoming water inside the top-load washer to help control splash and ensure proper fill distribution. Replacing a cracked or warped deflector restores correct water routing and can reduce leaking or overflow at the inlet. What it does:

• Directs incoming water from the inlet valve into the wash basket to reduce splashback.
• Helps maintain even water distribution during fill cycles.
• Prevents water from pooling near the inlet area that can cause leaks.
• A damaged or missing deflector may cause water to spray, spill, or fill unevenly.

• Disconnect power and shut off the water supply before starting any repairs.
• Inspect the inlet area and any gaskets; replace damaged seals to prevent leaks.
• Typically installs with basic tools; ensure the deflector is seated securely and test for leaks after reassembly.

The Tubing is an OEM part for Speed Queen commercial washing machines. This tubing is used to direct water flow throughout important systems within the washing machine.

Causes of bad tubing can include cracks, leaks, kinks or blockages developing over time due to regular use and the mechanical stresses of pumping water during wash cycles.

Symptoms of bad tubing include:

• Water leaks around connections points
• Slow or weak water flow
• Irregular or inconsistent water levels during cycles
• Loud noises from the water system
• Error codes related to water sensors or pumps

The Tub to Pump Hose is an OEM part for Speed Queen commercial washing machines. This hose connects the washer tub to the pump, allowing water to be drained out of the tub and released when cycles are complete.

Causes of a bad tub to pump hose can include mineral deposits building up over time, cracks or leaks developing in the rubber material, or accidental cuts or cracks from mishandling.

Symptoms of a bad tub-to-pump hose include:

• Water leaks inside or outside of the machine
• Inability to fully drain water after cycles
• Slow drain times
• Erratic water levels during fill cycles
• Error codes related to draining or water level sensors

This is a stainless-steel #8 x 1/2" Torx screw used to secure panels and components on Speed Queen appliances. Stainless construction resists corrosion for reliable fastened connections in laundry equipment. What it does

• Secures console, trim, panels, and internal brackets where a #8 x 1/2" Torx fastener is specified.
• Replaces missing or damaged screws that can cause loose panels, rattling, or misaligned components.
• Stainless-steel construction helps prevent rust in wet or humid laundry environments.
• Small, common fastener for service and reassembly after repairs.

• One stainless-steel #8 x 1/2" Torx screw.

• Use the correct Torx driver size to avoid stripping the screw head.
• Tighten finger-tight then snug; avoid over-torquing which can strip threads or crack plastic.
• Disconnect power (and water if applicable) before working on appliance internals to reduce shock or injury risk.

This control assembly operates the washer's drive system and on-board controls to run timed wash and spin cycles. Replaces a failed control to restore normal cycle sequencing and drive motor operation. What it does:

• Sends power and signals to the washer drive motor so the machine can agitate and spin
• Manages cycle timing and control board functions for proper wash cycles
• Engages safety interlocks and responds to user controls/commands
• May cause symptoms like the washer not starting, not agitating/spinning, or showing control errors when faulty

• One control assembly (drive, 120V)

• Disconnect electrical power before removing or installing the control to avoid shock
• Handle the board and connectors carefully; avoid static discharge and bent pins
• Verify connector locations and mounting before powering up to prevent short circuits

This pressure sensor harness connects the washer's pressure sensor to the control board so the machine can detect water level and run cycles correctly. Replacing a faulty harness restores reliable pressure signal transmission. What it does:

• Transmits the pressure sensor signal to the washer control for accurate water-level detection
• Helps prevent overfill, underfill, or incorrect cycle advancement when functioning properly
• Commonly replaced when the washer shows pressure-related error codes, erratic filling, or failure to advance
• Maintains sealed connector and wiring continuity to ensure consistent sensor readings

• Disconnect power before servicing to avoid shock or damage
• Inspect connectors and wiring for corrosion or pin damage; replace if any are compromised
• Route harness away from heat sources and sharp edges; secure with existing clips
• After install, run a diagnostic or a short cycle to ensure proper pressure readings and function

This small sealing washer fits the washer's water pressure assembly to help maintain a proper watertight seal at the pressure/valve connection. Replacing a worn washer reduces leaks and helps the fill/pressure system operate as intended. What it does

• Provides a watertight seal at the water pressure/valve connection to prevent leaks.
• Helps maintain correct pressure feedback to the washer's water control system.
• Wear or damage can allow leaking at the valve or inconsistent fill behavior.
• Simple, low-cost part commonly replaced when troubleshooting valve leaks.

• Turn off household water supply and unplug the washer before replacing.
• Remove the valve/pressure fitting carefully and replace the old washer with the new one, making sure it seats flat and undamaged.
• Inspect mating surfaces for debris or damage; clean before reassembly.
• If leaks or fill issues persist after replacement, inspect related seals, fittings, and the pressure switch/valve assembly.

A replacement cord lead-in that routes incoming power into the appliance and provides a secure connection point for the main wiring. Restores reliable electrical feed and helps eliminate intermittent power or no-power issues. What it does:

• Transfers household power from the external cord to the appliance's internal wiring
• Provides a stable inlet connection and strain relief for the incoming power cable
• Commonly replaced for symptoms such as no power, intermittent power, blown fuses, or visible damage/corrosion at the inlet
• Matches OEM fit and mounting for a direct replacement when the part number is correct

• One cord lead-in assembly

• Disconnect all power at the breaker or unplug the appliance before starting work
• Route wires and secure strain relief per OEM guidance; tighten terminal connections firmly but do not overtighten
• If wiring or terminal damage is present, replace or repair per local electrical code

This small replacement tray lid clip secures the washer's tray or lid trim to prevent unwanted movement and rattling. It restores a snug fit so the tray stays in place during normal use. What it does:

• Clips into the tray or lid flange to hold the trim or small access tray securely.
• Replaces broken, cracked or missing clips that allow the tray or lid to wobble or fall.
• Helps eliminate rattling noises caused by loose trim or trays.
• Restores proper alignment so the tray/lid stays seated during operation.

• Unplug the appliance or disconnect power before beginning any work.
• Access the clip by opening/removing the tray or lid; trim or control panels may need removal.
• Clip installs by snapping into the mating slot—no special tools typically required; use care to avoid damaging surrounding trim.
• After installation, test for secure fit before returning the appliance to service.

This driven pulley is the replacement transmission pulley that guides the drive belt and transfers motor power to the washer agitator and tub. Restores proper belt tracking and drivetrain engagement for top-load washers. What it does:

• Replaces a worn or damaged transmission-driven pulley to restore smooth belt movement
• Guides and supports the drive belt, preventing slipping and misalignment
• Helps maintain proper power transfer from the motor to the transmission and tub
• Commonly used when you hear squealing, grinding, or notice poor agitation/spinning

• Disconnect power to the washer before servicing to avoid electrical or mechanical injury
• Access typically requires removing cabinet or lower front panel; follow OEM service manual steps
• Inspect belt and related components; replace any worn or damaged parts for best results

A size #20 hose clamp used to secure flexible hoses to fittings on laundry appliances, helping prevent leaks and keep hoses firmly attached during operation. Simple, low-profile design for reliable hose connections. What it does:

• Secures washer drain and inlet hoses to fittings to reduce leak risk.
• Prevents hoses from slipping off under pressure or vibration.
• Helps maintain consistent water flow by keeping connections tight.
• Fits standard #20 hose diameter applications commonly used on laundry equipment.

• One size #20 hose clamp.

• Use a flathead screwdriver or nut driver to tighten; turn until snug—do not overtighten to avoid hose damage.
• Inspect hose and fitting for cracks or corrosion and replace if needed before installing the clamp.
• After installation, run a short test cycle and check for leaks; retighten if necessary.
• Disconnect power and water supply before servicing the appliance.