Bx22 Parts

This is a flexible rubber seal that attaches around the perimeter of the refrigerator door. It creates an airtight seal when the door is closed to maintain proper internal temperature and prevent warm air from entering. Replace this gasket if you notice condensation forming around the door edges, the refrigerator running constantly, or if the seal is torn, cracked, or no longer holding the door closed tightly.

Refrigerator not cooling or running constantly? The compressor circulates refrigerant to maintain temperature. This repair requires refrigerant handling.

This replacement screw fastens internal components and panels so parts stay secure and quiet. It's a direct-fit fastener used where the original mounting screw is missing or damaged to restore proper assembly. What it does:

• Secures panels, brackets or components to prevent movement and vibration
• Restores proper alignment for covers and access panels
• Stops rattling or loose-fitting parts caused by a missing or stripped screw
• Works as the factory-specified fastener for the original mounting point

• The screw location and type before installing; use the original hole and thread
• Power off and disconnect the appliance before accessing internal components
• Start the screw by hand to avoid cross-threading, then snug with the appropriate screwdriver
• Do not overtighten — stop once the part is secure to avoid stripping or cracking

This drive coupling connects the washer motor to the transmission, transferring power to spin and agitate the tub. Replacing a worn coupling restores proper drivetrain engagement and reduces slipping, grinding, or loss of agitation. What it does:

• Transfers rotational force from the motor to the transmission so the washer can agitate and spin.
• Failsafe for worn motor-to-gearcase connection; a broken coupling commonly causes no-agitate or no-spin symptoms.
• Can produce burning smell, loud grinding, or slipping when deteriorated.
• Helps prevent further damage to the motor or transmission by isolating shock loads.

• Disconnect power and water before starting any repair.
• Basic disassembly of the washer cabinet and access to the motor/transmission area is required.
• Verify correct alignment of tabs/slots during installation to ensure proper engagement.

Replacement mounting screw for refrigerators, freezers, and air conditioners. Secures panels, brackets, and internal components. Order now if missing or stripped.

This overload is a thermal protection device that mounts on the motor/compressor and opens the circuit when excessive heat or current is detected. Replacing a weak or failed overload helps restore safe startup and protects the windings from damage. What it does:

• Monitors motor/compressor temperature and current draw
• Interrupts power on overheat/overload to prevent damage
• Aids troubleshooting of start/run issues when paired with the start device
• Common symptoms: hums then clicks off, won't start, intermittent shutdown, frequent tripping

• 1 thermal overload protector

• Disconnect power before servicing; allow components to cool
• Access the terminal area on the motor/compressor; remove any cover
• Note/photograph wire positions; transfer wires and fully seat the new overload on the correct terminal
• Inspect the start relay, capacitor, and terminals for heat damage; replace any compromised parts

A small replacement clip-style retainer that secures the appliance toe grille to the cabinet, keeping the grille flush and in place. Replaces worn or broken clips to restore proper fit and appearance. What it does:

• Secures the toe/grille panel to the appliance cabinet so the grille stays aligned and snug
• Stops the grille from sagging, rattling, or popping off during use
• Fits into designated mounting slots or tabs to lock the grille in place
• Commonly replaced when clips are cracked, missing, or loose

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the toe grille by removing any screws or releasing retaining tabs per your model's service instructions
• Press the clip into the grille/cabinet mounting slot until it snaps in place; verify the grille seats evenly
• If multiple clips are damaged, replace all needed clips for a secure fit

This thin plastic or metal shim provides proper alignment and spacing for your refrigerator door hinge. It ensures the door closes properly and maintains correct gaps around the door seal. Install this shim if your refrigerator door doesn't align properly, has uneven gaps, or doesn't seal tightly.