Cdc22p2aww Parts

A replacement shaft seal that restores the watertight seal where a rotating shaft passes through the tub or housing, helping prevent leaks and protecting bearings and internal components from moisture and contamination. What it does:

• Seals the gap around a rotating shaft to stop water from leaking out of the tub or housing.
• Helps keep grease and contaminants contained around bearings and shaft openings.
• Common symptom link: replace when you see water on the floor, visible leaks near the shaft, or wet/soiled bearing areas.
• Small, inexpensive part that prevents further damage to nearby components when installed promptly.

• Disconnect power and turn off water supply before beginning work; drain remaining water from the appliance.
• Access usually requires partial disassembly (remove panels/tub or transmission as applicable); follow OEM instructions.
• Inspect shaft and housing for wear or damage; clean mating surfaces before installing the new seal.
• Test appliance for leaks after reassembly and before returning to regular use.

A replacement leveling leg that stabilizes your appliance and allows height adjustment for a secure, level install. Restores proper alignment to reduce rocking, vibration and uneven door gaps. What it does:

• Raises and levels the appliance so all feet contact the floor evenly.
• Stops rocking and excessive vibration that can cause noise or wear.
• Helps restore proper drainage and door alignment by correcting tilt.
• Matches original fit and function for reliable support.

• Disconnect power (and water for appliances with plumbing) before servicing.
• Raise or support the appliance safely before removing or adjusting legs.
• Turn the leg to raise or lower; make small adjustments and recheck level.
• Use common hand tools (wrench or pliers) and avoid forcing damaged threads.

This screw kit provides replacement fasteners used to secure appliance panels and internal components, helping restore proper fit and reduce vibration or rattling caused by missing or damaged screws. Ideal for maintenance and small repairs. What it does:

• Replaces missing, stripped, or damaged screws to restore secure panel and component attachment
• Helps eliminate rattling, vibration, and loose or misaligned panels
• Allows reassembly after part replacement or routine service
• Works with the appliance's original mounting points and threaded holes

• Always disconnect power and, if applicable, gas supply before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping screw heads
• Tighten screws snugly but avoid over-torquing which can strip threads or crack panels
• Keep small fasteners away from children and pets; work on a stable, well-lit surface

Color: Stainless steel

This is a replacement 6-32 x 3/8" screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening for loose or missing fasteners so parts stay aligned and stable. What it does:

• Secures trim, panels, brackets or small components to the appliance frame
• Stops rattling or movement caused by a missing or stripped screw
• Helps maintain proper alignment of control panels and access panels
• Provides the correct thread engagement for safe, stable fastening

• One replacement screw (6-32 x 3/8")

• Disconnect power before accessing internal components
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or components
• Keep removed hardware organized and compare sizes before installation

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

This electric heating element generates the high heat needed for your appliance to reach operating temperatures, restoring normal heating performance and cycle effectiveness. Use the correct replacement for safe, reliable heat output. What it does:

• Heats the appliance's air or oven cavity so cycles reach intended temperatures
• Restores proper heating when the appliance runs but produces little or no heat
• Helps resolve long cycles or poor performance caused by a failed element
• Replaces a worn or open element that shows visible damage or electrical failure

• One heating element

• Disconnect all power before beginning service to avoid shock or injury
• Handle the element carefully to avoid bending or kinking the tubing/coil
• Verify electrical connections are secure and correct before restoring power

Note: For faucet adapter

A replacement appliance door handle that restores a secure grip and proper operation to a worn or broken handle. Designed to match the original mounting style for a clean, factory-fit appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door smoothly
• Replaces cracked, loose, or broken handles that affect normal door use
• Restores correct alignment and leverage to reduce strain on door components
• Helps prevent accidental drops or slippage when grabbing the door

• One replacement handle

• Remove power and empty the door area before starting any repair
• Typical install requires removing trim or screws; use manufacturer-recommended fasteners
• Retain original mounting hardware unless the new handle explicitly includes replacements

This is a machine screw used to secure appliance panels and components where an 8-32 thread fastener is specified. It provides a reliable hold for control panels, brackets, and interior assemblies. What it does:

• Fastens panels, brackets, and small components to the appliance chassis
• Holds control assemblies and trim pieces in place
• Maintains secure connections that prevent vibration-related loosening
• Works where an 8-32 coarse-thread machine screw of short length is required

• One 8-32 x 3/8" machine screw

• Use the correct driver (Phillips or slotted) to avoid stripping the head
• Thread into metal or nut/insert; do not overtighten to prevent thread damage
• Disconnect power and remove any panels as required for safe access

This switch holder secures a small appliance switch or actuator in the correct position so the control can detect and respond reliably. Replacing a cracked or broken holder restores consistent switch alignment and helps prevent intermittent operation. What it does:

• Holds the switch or actuator steady in the correct position for reliable electrical contact and activation
• Keeps the switch aligned so buttons, door/lid actions, or control functions register properly
• Common symptom: appliance function won't engage or is intermittent when the switch is loose or the holder is damaged
• Prevents further wear on the switch by keeping it from shifting or rubbing against surrounding parts

• Disconnect power (unplug or shut off breaker) before servicing the appliance
• Remove the control panel or access panel to reach the holder; keep small clips and screws organized
• Inspect the switch and actuator for damage while replacing the holder; replace any damaged mating parts