Cgs985 Parts

The Blower Motor is an OEM part for GE ranges. Within the oven cavity, it circulates air to help distribute heat evenly for thorough cooking.

Causes of a bad Blower Motor include wear from long term use, residue buildup on fan blades inhibiting air movement, or electrical issues such as loose wiring connections or a burned out motor coil.

Symptoms of a bad Blower Motor are:

• Inconsistent or improper baking and broiling
• Hot and cold spots inside the oven cavity
• Extended cooking times needed for foods

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This cable clamp secures the appliance power cord where it enters the cabinet, protecting wiring from pull and chafe for safer, more reliable operation. Designed to hold the cord firmly in place and prevent accidental disconnection. What it does:

• Acts as a strain relief to prevent the power cord from pulling into or away from the appliance
• Protects wiring from abrasion and sharp edges at the entry point
• Helps maintain a secure electrical connection to reduce intermittent power issues
• Commonly used where the cord passes through a rear or bottom access panel

• Disconnect power before inspecting or replacing the clamp to avoid shock or injury
• Install at the cord entry so the clamp captures the cord jacket; tighten fastener securely but do not over-torque
• Verify the cord is correctly routed and not pinched when reassembling panels
• If any wiring or the cord jacket is damaged, replace the cord before restoring power

A receiver hinge that secures and supports an oven door hinge pin to keep the door aligned and operating smoothly. Replaces a worn or broken receiver to restore proper door fit and movement. What it does

• Accepts and retains the oven door hinge pin so the door opens and closes correctly.
• Supports door weight to prevent sagging or uneven alignment.
• Helps the door latch and seal properly for safe, consistent operation.
• Commonly replaced when the door drops, rubs, or will not stay closed.

• One receiver hinge

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the oven door or access panel per the service manual for safer installation.
• Use basic hand tools; check hinge pins and mating hardware for wear and replace if needed.

This oven light gasket fits between the glass lens and the oven liner. It restores a proper seal around the light opening to help keep grease and moisture out of the light cavity and hold the lens securely in place. What it does:

• Seals the joint between the oven light lens and the cavity wall
• Helps prevent grease and moisture from entering the light assembly
• Keeps the lens snug to reduce looseness or rattling
• Replace if the gasket is cracked, flattened, brittle, missing, or if moisture/grease is visible around the lens

• One oven light lens gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/retainer as your model requires (unscrew lens or release clips)
• Note gasket orientation and clean the mating surfaces
• Seat the new gasket evenly and reinstall the lens; do not overtighten the glass

The Knob Assembly is an OEM component for GE gas ranges. These knobs are turned to adjust oven or cooktop burner settings. 

Symptoms of a bad knob assembly include:

• Loose, gritty, or difficult movement when adjusting the temperature 
• Faded, cracked or peeling of installed knob surfaces
• Knobs no longer stay securely in position 

Causes of bad knob assemblies include wear over many cooking cycles that degrade plastic and rubber materials. Heat, grease exposure, and cleaning chemicals also corrode superficial finishes.

This part is also compatible with some Hotpoint and RCA gas range models.

This dual water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring normal water delivery when the original valve fails. Reliable replacement for disrupted water supply or intermittent dispensing. What it does:

• Directs water to the icemaker and dispenser via two separate inlet ports/solenoids
• Stops water flow when valves fail, causing no water or no ice production
• Can cause continuous water flow or leaks if a valve sticks
• Restores normal dispensing and ice-making when replaced

• Disconnect power and shut off the water supply before starting any repair
• Replace with matching orientation and secure mounting to avoid kinks in supply lines
• Verify connections and test for leaks after restoring power and water

This 1/4-20 screw secures panels, brackets, and other assemblies in your appliance. It restores a tight, reliable hold when an original fastener is missing, stripped, or corroded.

• Fastens components that require a 1/4-20 threaded screw
• Helps keep panels and assemblies aligned and rattle-free
• Direct replacement for worn, rusted, or lost hardware
• Common symptoms: loose or vibrating parts, misaligned brackets, missing fastener

• Disconnect power; turn off gas supply before servicing
• Allow the appliance to cool; wear gloves and eye protection
• Start threads by hand to avoid cross-threading; use the correct driver/tool
• Tighten snugly—do not overtighten to prevent stripping or damage

The Oven door hinge is an OEM part for GE ranges. This right side hinge is responsible for securely and smoothly opening and closing the oven door. It allows for comfortable access in and out of the oven cavity.

Causes of a bad hinge can include wear and tear from repeated opening and closing of the door over time, stress from excessive weight on the door, or damage from impact.

Symptoms of a bad hinge include:

• The door not opening or closing properly
• Increased resistance or hesitation when operating the door
• Loosening or sagging of the door
• Uneven gaps around the door frame

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This small replacement bumper cushions and protects the appliance frame/trim where panels meet, helping reduce vibration, chipping and rattles for a cleaner, quieter fit. Ideal when the original bumper is worn, cracked or missing. What it does:

• Cushions contact between the frame/trim and adjacent panels to reduce noise and prevent damage
• Helps maintain proper panel alignment and sealing where the trim meets the cabinet
• Reduces rattling or vibration caused by loose or degraded trim pads
• Restores protective spacing that prevents chips or scratches to finished surfaces

• One frame front bumper

• Disconnect power to the appliance before starting work and follow all safety precautions
• Usually installs by pressing into a slot or onto a mounting surface after removing the trim piece; some trim removal may be required
• Inspect mating surfaces for damage or debris and clean before installing the new bumper
• Replace with the exact part number only; do not force or modify the bumper to fit

The Glass & Touch Board Assembly is an OEM part for GE gas ranges. It includes both the outer glass panel that protects the touch controls, as well as the internal touch board. This assembly serves as the interface between the user and the oven. 

Symptoms of a bad Glass & Touch Board Assembly include:

• Glass panel cracked, broken or unsecured  
• Touch zones failing to work properly or at all
• Glitches in temperature/mode selection
• Oven operation affected or unpredictable

Causes of failure can be due to cracks or chips in the glass over time, or damage/wear to the internal touch board components.

This OEM GE replacement part is also compatible with Hotpoint, RCA and some Kenmore models.

A replacement door hinge that supports and guides a refrigerator door for smooth opening and reliable sealing. Restores proper alignment and helps prevent door sagging, rubbing, and gaps that allow cold air loss. What it does:

• Secures the refrigerator door to the cabinet and provides the pivot point for opening and closing.
• Restores correct door alignment to improve sealing and reduce cold-air leakage.
• Stops rubbing, scraping, or uneven gaps caused by a worn or bent hinge.
• Reduces noise and binding during door movement when hinge wear is the cause.

• One door hinge.

• Unplug the appliance or disconnect power before beginning any repair.
• Support the door while removing/installing the hinge to prevent injury or damage.
• Keep existing screws and any trim/cover pieces unless replacing them with included hardware; only state what ships if explicitly provided.

The Switch Harness is an OEM part for GE gas ranges. It connects various control interfaces like knobs, buttons and displays to the appliance's systems module. 

Causes of failure involve wiring cracking from repeated flexing at connection points throughout years of use, pinched bundles restricting consistent conductivity, and typical insulation degradation over extended heat exposure.

Symptoms of a faulty harness include:

• Burners or oven failing to ignite or operate as selected
• Inability to accurately set temperature or function controls  
• Intermittent or unstable power to surfaces and components

This OEM part is also compatible with Hotpoint and RCA models.