Dcvh480ekoww Parts

A small nylon wire tie used to secure wiring harnesses and keep wires organized and away from moving or hot components. Helps reduce vibration and prevent chafing for safer, quieter appliance operation. What it does:

• Bundles and secures loose wires to prevent rubbing or contact with moving parts
• Keeps wiring routed neatly to reduce vibration noise and potential wear
• Helps prevent accidental wire disconnection or snagging during service
• Simple mechanical fastening—no tools or adhesives required for placement

• Disconnect power to the appliance before starting any work
• Route wires as needed, loop the tie around the bundle, and pull snug—avoid over-tightening which can damage insulation
• Trim excess tail with cutters; keep cut end tucked away from sharp edges

This push-mount open clamp secures wiring, hoses, or small tubing to appliance panels or flanges for tidy routing and reduced strain. Durable plastic design keeps lines organized and prevents chafing where components pass through or along cabinet edges. What it does:

• Holds wires, harnesses, or small tubing in place to prevent rubbing and wear
• Push-mount style snaps into a panel hole or slot for tool-free attachment
• Open clamp design allows lines to be inserted or removed without full disassembly
• Helps reduce strain on connectors and routed lines that can cause intermittent faults

• Disconnect power to the appliance before servicing electrical components
• Push the retainer stem into the matching panel hole until it snaps into place
• Insert wiring or tubing into the open clamp; use gentle pressure to avoid over-stressing lines
• Replace any damaged fasteners and verify routing does not interfere with moving parts

This is a hinge-header screw used to secure door hinge assemblies—provides the correct fit and thread size for a tight, stable hinge connection to keep doors aligned and operating smoothly. What it does:

• Secures the hinge header to the appliance chassis or door hinge assembly
• Restores proper hinge alignment to eliminate door sag or uneven closing
• Prevents looseness that can cause noise, rubbing, or misalignment
• Matches M5 thread and 12mm length for the intended hinge mounting point

• Support the door or hinge assembly before removing or installing the screw to avoid dropping or damaging the door
• Use the correct-sized driver to avoid stripping the head; tighten snugly but avoid over-torquing
• Disconnect power or follow appliance-specific safety procedures if removing panels near electrical components

This flat washer provides a durable spacer and load-bearing surface for appliance fasteners, helping secure parts and reduce wear. It restores proper fit where a worn or missing washer causes looseness or vibration. What it does

• Distributes nut or bolt load to protect mating surfaces and prevent pull-through
• Maintains proper fastener spacing to help prevent loosening from vibration
• Helps reduce rattling and wear where panels or components meet
• Used wherever a flat metal washer is specified in the appliance assembly

• Turn off power and unplug the appliance before accessing fasteners
• Match washer size and orientation to the original during installation
• Use appropriate hand tools and avoid overtightening fasteners

This blower wheel nut secures the dryer blower wheel to the motor shaft, keeping the wheel stable for proper airflow and drying. A simple replacement that stops wobble and helps restore quieter, more efficient operation. What it does:

• Holds the blower wheel firmly on the motor shaft to prevent slipping or wobbling
• Prevents noise caused by a loose blower wheel
• Helps maintain consistent drum airflow for better drying performance
• Reduces wear on the blower assembly by keeping parts aligned

• Disconnect power before starting any repair to avoid shock or injury
• Access may require removing the dryer front panel or blower housing depending on model
• Typically removed/installed with a socket or pliers; hold the blower wheel to prevent spinning while tightening
• Tighten securely but avoid over-torquing to prevent thread damage

This is an M3 x 16 mm machine screw used to fasten small appliance components. It provides secure, low-profile attachment for panels, brackets, and assemblies, restoring proper fit and preventing rattles or looseness. What it does:

• Secures panels, brackets, or small components to appliance frames and assemblies
• Restores proper alignment and eliminates vibration or rattling caused by missing or loose fasteners
• Replaces stripped, missing, or corroded screws to maintain safe equipment operation
• Works where a metric M3 x 16 mm threaded fastener is specified by the manufacturer

• Use the correct screwdriver or bit to avoid stripping the head
• Thread components by hand first, then snug; do not overtighten
• Replace any damaged mating hardware (nuts, captive clips) for secure fastening
• Disconnect power and follow appliance safety procedures before servicing