De5fhaxss02 Parts

Lifter fin that mounts inside the rotating drum to tumble laundry. Replace if cracked, broken, or missing. Installs with screws for proper load movement.

Dryer stopped heating or takes hours to dry? This heating element restores proper heat output. Typical repair takes about an hour with basic tools.

Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Single screw used to secure panels, brackets, and internal components to the dryer frame. Replaces lost, stripped, or damaged fasteners during repairs.

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

This terminal block provides the electrical connection point where the power cord wires attach to the dryer's internal wiring. It is typically mounted on the rear of the dryer near the power cord entry point. Replace this part if you notice burn marks, melted plastic, loose wire connections, or if the dryer is not receiving power properly.

Ceramic dryer heating element terminal block.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Hex washer head ,10-32 x 0.375. Ground

Spesc: #12 pozi - drive

This small retainer clip secures trim, panels, or components in place to prevent rattling and keep parts aligned. It's a simple replacement that restores proper fit and reduces vibration or loose panels. What it does:

• Holds appliance trim or panel pieces in position to prevent movement and noise
• Helps keep wiring or small components routed and secured away from moving parts
• Stops gaps or misalignment that can cause rubbing or vibration sounds
• Restores the intended fit where a worn or broken clip allows play

• Disconnect power to the appliance before starting any repair
• Access the clip location by removing the applicable trim or panel per your model's service instructions
• Use common hand tools; replace broken clips with the identical style to ensure proper fit
• Replace all matching clips for consistent fit

Suspension spring for dryers. Supports the drum and absorbs vibration during operation. Replace if stretched, broken, or causing excessive drum movement.

Replace your dryer's timer knob if it's cracked, broken, or missing. This control knob installs on the timer shaft to let you set cycle times.