De650kdw-2 Parts

Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

Ceramic dryer heating element housing insulator.

Replacement mounting screw for various appliances. Needed when original screws are stripped, lost, or damaged during repair or maintenance work.

Hex washer head ,10-32 x 0.375. Ground

Suspension spring for dryers. Supports the drum and absorbs vibration during operation. Replace if stretched, broken, or causing excessive drum movement.

Dryer drum shaft that supports the drum and connects to the bearing. Replace if worn, damaged, or causing squeaking noises. Verify fit with your model.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Replace your dryer's timer dial if it's cracked, broken, or won't turn properly. This control dial mounts on the timer shaft to set drying cycles.

Dryer stopped heating or takes hours to dry? This heating element restores proper heat output. Typical repair takes about an hour with basic tools.

This block is a small mounting spacer used to secure and align components inside the appliance, helping maintain proper fit and operation. It replaces worn or broken mounting blocks to restore stable support and alignment. What it does:

• Provides a stable mounting surface or spacer between cabinet components
• Holds panels or assemblies in correct position to prevent rubbing or misalignment
• Helps reduce vibration or shifting of the connected parts during operation
• Commonly replaced when cracked, broken, or missing

• One mounting block

• High-level replacement; may require removing panels or trim to access mounting location
• Use appropriate hand tools and keep fasteners organized for reassembly
• Disconnect power before servicing any electrical components

Ceramic dryer heating element terminal block.

This small retainer clip secures trim, panels, or components in place to prevent rattling and keep parts aligned. It's a simple replacement that restores proper fit and reduces vibration or loose panels. What it does:

• Holds appliance trim or panel pieces in position to prevent movement and noise
• Helps keep wiring or small components routed and secured away from moving parts
• Stops gaps or misalignment that can cause rubbing or vibration sounds
• Restores the intended fit where a worn or broken clip allows play

• Disconnect power to the appliance before starting any repair
• Access the clip location by removing the applicable trim or panel per your model's service instructions
• Use common hand tools; replace broken clips with the identical style to ensure proper fit
• Replace all matching clips for consistent fit

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support