Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Missing ice trays or need extra ice capacity? This stackable ice cube tray fits most refrigerators. Simple DIY installation takes just minutes.
Just missed having decent ice trays. The only ones I could find were either: 1. Expensive 2. Flimsy - only lasted a couple of months 3. Silicone-bottomed that half the compartments leak after a few uses These are the wonderful old fashioned kind that are easy to use and last forever. Just didn’t think I’d find them again! Read more
Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.
Dryer not heating or shutting off early? The safety thermostat monitors temperature and cuts power when it gets too hot. Tests quickly with a multimeter.
Dryer not heating properly or overheating? This cycling thermostat regulates temperature by cycling the heating element on and off. Moderate DIY repair.
Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.
Fix a dryer burner that starts then goes out with this gas valve coil. DIYers can test resistance with a multimeter and replace in under an hour.
I ohm metered the sensors to determine which one was bad (open) Looked up the part on the parts drawing. Ordered part and had the dryer running 2 days later Read more
Leveling foot assembly with bolt, pad, and nut restores a stable, level base for your washer. Replace worn, stripped, or missing feet to adjust height.
Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.
Replaced heater. Read more
Mounting screw for range bottom drawer assembly. Replaces lost, stripped, or damaged screws. 6-20 x 0.312 inch size. Essential hardware for drawer repair.
Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.
I submitted my question, and problem to Appliances Pro, and they informed me that the problem was with my gas valve, or gas safety value. Read more
Dryer won't heat or shuts off too soon? This high-limit thermostat prevents overheating by cutting power when temps get too high. Easy DIY fix.
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Replacement screw for securing dryer panels, brackets, and baffles. Ideal for replacing missing, stripped, or rusted hardware to restore a secure fit.
Purchased timer and baffle, and my appliance repairman installed them. I could get the parts cheaper than he could from his supplier; he asked me for the Appliance Parts Pros website address! Read more
Routes defrost water from the freezer to the drain pan. Replace if cracked, clogged, or disconnected to prevent leaks and water pooling inside your unit.
Single screw used to secure panels, brackets, and internal components to the dryer frame. Replaces lost, stripped, or damaged fasteners during repairs.
At first i just bought the belt, started dryer and off came the belt, and yes it was in place,looking at the idler arm it had a lot off back and forth movement so i ordered the whole assembly but the spring which no one has.put it all together again but drum barely turned.. so back apart and belt was in place. took the idler spring out cut 4 loops off it re did the end so it would hook on idler arm.and that did the trick.runs like new. Read more
Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.