Dg575 Parts

Replace your dryer's timer dial if it's cracked, broken, or won't turn properly. This control dial mounts on the timer shaft to set drying cycles.

Size: 8-32 x .312 inch.

This clip secures the lint screen frame to the dryer housing, keeping the lint filter properly seated during operation. It snaps into place to hold the frame firmly so the lint screen does not shift or rattle. Replace this clip if it is broken or missing, which can cause the lint frame to sit loosely or allow the lint screen to move out of position.

This replacement screw is a direct-fit fastener used to secure appliance panels and components, restoring proper fit and reducing movement. Ideal when original screws are stripped, missing, or damaged. What it does:

• Secures panels, trim, brackets, and other serviceable components to prevent rattling or misalignment
• Matches original fastener form for correct fit and reliable function
• Helps restore proper clearance and component alignment after repair
• Safe, general-purpose replacement for common appliance fastening needs

• Turn off power and disconnect the appliance before accessing internal components
• Use the correct screwdriver or bit; avoid overtightening to prevent thread or part damage
• Keep hardware and small parts away from children and pets

This dishrack replaces a damaged, rusted, or warped rack to restore smooth loading and secure support for dishes. A solid rack keeps items upright for better spray coverage, cleaner results, and helps prevent rust transfer and chipping.

• Holds and organizes plates, bowls, and cookware for proper spacing and spray access
• Provides stable support to reduce tipping and breakage during wash cycles
• Replaces racks with rust, broken wires, or bent/missing tines
• Can help resolve issues like rust marks on dishes and loading difficulties

• Disconnect power at the breaker before servicing
• Open the door; slide the old rack out—on some models, release rack stops to remove
• Transfer any reusable accessories from the old rack to the new rack if applicable
• Wear cut-resistant gloves; set the new rack on the rails and verify smooth movement and proper door closure

The Dryer Door Latch Kit is an OEM part for Whirlpool dryers. It ensures the dryer door stays securely closed during operation, allowing the dryer to function correctly and safely. This kit typically includes the latch, strike, and necessary mounting hardware for easy installation.

Causes of a bad door latch can include wear and tear from frequent use, accidental damage from forceful closing, or alignment issues due to the door being knocked out of place. A faulty latch can prevent the dryer from starting or cause it to stop mid-cycle if the door doesn't stay closed.

Symptoms of a bad dryer door latch include:

• The dryer door not staying closed
• The dryer not starting or stopping unexpectedly during a cycle
• Difficulty in closing or latching the door
• Loose or misaligned latch components

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Lifter fin that mounts inside the rotating drum to tumble laundry. Replace if cracked, broken, or missing. Installs with screws for proper load movement.

Pop rivet secures sheet-metal panels, brackets, and burner jar lids on appliances. Replace missing, drilled-out, or damaged rivets for permanent hold.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Single screw used to secure panels, brackets, and internal components to the dryer frame. Replaces lost, stripped, or damaged fasteners during repairs.

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support